Poulan 402559, 96012004701 manual Check Battery See Fig

Page 7

ASSEMBLY

SEAT SHOULDER

BOLT

SEAT PAN

FLAT WASHER

02464

ADJUSTMENT

KNOB

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fi ll fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this man- ual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Always Wear EYE Protection During Operation PB19H42LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigADD Gasoline Before Starting the EngineTo Transport See Figs Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

402559, 96012004701 specifications

The Poulan 96012004701 and 402559 are innovative outdoor power equipment tools designed for both professional landscapers and avid gardeners. These tools are crafted with advanced technologies and features that enhance performance, reliability, and ease of use.

One of the standout features of these Poulan products is their powerful engine performance. Both models typically come equipped with robust two-cycle engines that deliver reliable power with efficient fuel consumption. This means that users can tackle a variety of outdoor tasks without the worry of frequent refueling or interruptions. The engines are designed to be lightweight, reducing user fatigue during prolonged usage.

Durability is another hallmark of the Poulan 96012004701 and 402559 models. Constructed with high-quality materials, these tools can withstand the rigors of outdoor environments. Whether cutting through thick brush or trimming delicate hedges, users can rely on the sturdy build to handle various applications. Additionally, the components are often resistant to wear and tear, ensuring longevity and consistent performance.

User comfort and ergonomics are central to the design of these models. They are typically equipped with adjustable handles that provide a customized grip, allowing for comfort during extended use. The anti-vibration technology integrated into the handle helps to reduce fatigue and strain on the arms and hands, making each job more manageable.

In terms of versatility, the Poulan 96012004701 and 402559 are designed to tackle a wide range of outdoor tasks. Whether it’s edging a garden bed, trimming overgrown areas, or maintaining a manicured lawn, these tools are adaptable to the demands of the job. The ease of blade or attachment changes allows users to switch tasks swiftly, making these models efficient and time-saving.

Safety features also play an essential role in the design of these Poulan products. They commonly include features like protective guards and easy-start technologies, aimed at minimizing the risks associated with outdoor power equipment. The user-friendly starting mechanisms reduce the chances of accidental starts, providing peace of mind while operating.

In conclusion, the Poulan 96012004701 and 402559 combine power, durability, and user-centric design, making them reliable choices for anyone looking to enhance their landscaping capabilities. Whether for home use or professional landscaping services, these models stand out for their efficiency and performance, ensuring that outdoor tasks are completed with ease and precision.
Top Page Image Contents