Poulan 271491 manual Excessive

Page 27

TROUBLESHOOTING CHART

 

PROBLEM

 

CAUSE

CORRECTION

 

 

 

 

 

 

Loss of power

Cutting too much grass/too

• Set in “Higher Cut” position/

 

 

 

fast.

 

reduce speed.

 

 

Throttle in “CHOKE”

Adjust throttle control.

 

 

 

position.

 

 

 

 

Build-up of grass, leaves

• Clean underside of mower

 

 

 

and trash under mower.

 

housing.

 

 

Dirty air filter.

Clean/replace air filter.

 

 

• Low oil level/dirty oil.

• Check oil level/change oil.

 

 

Faulty spark plug.

• Clean and regap or change

 

 

 

 

 

spark plug.

 

 

Dirty fuel filter.

Replace fuel filter.

 

 

• Stale or dirty fuel.

• Drain fuel tank and refill with

 

 

 

 

 

fresh gasoline.

 

 

Water in fuel.

• Drain fuel tank and carbure-

 

 

 

 

 

tor, refill tank with fresh

 

 

 

 

 

gasoline and replace fuel

 

 

 

 

 

filter.

 

 

• Spark plug wire loose.

• Connect and tighten spark

 

 

 

 

 

plug wire.

 

 

• Dirty engine air screen/fins.

• Clean engine air screen/fins.

 

 

Dirty/clogged muffler.

Clean/replace muffler.

 

 

• Loose or damaged wiring.

Check all wiring.

 

 

Carburetor out of

See “To Adjust Carburetor”

 

 

 

adjustment.

 

in Service Adjustments

 

 

 

 

 

section.

 

 

• Engine valves out of

Contact an authorized

 

 

 

adjustment.

 

service center/department.

 

 

 

 

 

 

 

Excessive

Worn, bent or loose blade.

Replace blade.

 

vibration

 

 

 

Tighten blade bolt.

 

 

Bent blade mandrel.

Replace blade mandrel.

 

 

Loose/damaged part(s).

Tighten loose part(s).

 

 

 

 

 

Replace damaged parts.

 

 

 

 

 

 

 

Engine continues

Faulty operator-safety

Check wiring, switches and

 

to run

 

presence control system.

 

connections. If not corrected,

 

when operator

 

 

 

contact an authorized

 

leaves seat with

 

 

 

service center/department.

 

with attachment

 

 

 

 

 

clutch engaged

 

 

 

 

 

Poor cut - uneven

Worn, bent or loose blade.

Replace blade. Tighten

 

 

 

 

 

blade bolt.

 

 

• Mower deck not level.

Level mower deck.

 

 

• Buildup of grass, leaves,

• Clean underside of mower

 

 

 

and trash under mower.

 

housing.

 

 

Bent blade mandrel.

Replace blade mandrel.

 

 

• Clogged mower deck vent

• Clean around mandrels to

 

 

 

holes from buildup of

 

open vent holes.

 

 

 

grass, leaves, and trash

 

 

 

 

 

around mandrels.

 

 

27

Image 27
Contents Model no Table of Contents III. Children IV. ServiceWash hands after handling U1R Product SpecificationsCustomer Responsibilities API-SF-SJUnassembled Parts Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Install Seat Check Brake System Check Tire PressureCheck for Proper Position of ALL Belts Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine ADD Gasoline To Start EngineMowing Tips Before Each USE General Recommendations Lubrication ChartTractor Belts Clean AIR ScreenEngine Transaxle CoolingCleaning To Remove Mower To Install MowerBelt Removal To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltBelt Installation To Adjust BrakeTo Replace Motion Drive Belt To Remove Wheel for Repairs To Adjust Steering Wheel ALIGN- MentReplacing Battery Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Storage BatteryProblem Cause Correction Troubleshooting ChartExcessive Mower blades will Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation