Poulan 191606 manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 23

BELT INSTALLATION -

1.Carefully work new belt down between transaxle belt keepers and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll around the top groove of engine pulley.

4.Install belt through stationary idler and clutching idler.

5.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

6.Install mower (See “TO INSTALL MOWER” in this section of manual).

Engine

Pulley

Clutching

Idler

Stationary

Idler

Center

Span

Keeper

Transaxle

Pulley

00811

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1.Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

2.Loosen adjustment bolt in front of the right rear wheel.

3.Position the gear shift lever in the neu- tral (N) position.

4.Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

Gearshift Lever

Retaining Washers

Ring

Axle

Cover

00663

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

02239

Adjustment Bolt

Neutral

Lock Gate

 

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short

23against tractor chassis.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. CO1842STA Warranty Table of ContentsII. Slope Operation Safety RulesGeneral Operation Do not IV. ServiceIII. Children Safety Rules API-SF-SJ Product SpecificationsCustomer Responsibilities Unassembled Parts Before Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonCheck Battery Check for Proper Position of ALL Belts Install Mulcher PlateTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments To Operate MowerTo Operate on Hills To TransportADD Gasoline Before Starting the EngineTo Start Engine Check Engine OIL LevelMowing Tips Before Each USE MaintenanceGeneral Recommendations Tractor Engine Cleaning Service and AdjustmentsFRONT-TO-BACK Adjustment To Install MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Motion Drive Belt To Check and Adjust BrakeTo Replace Mower Blade Drive Belt Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTransaxle Gear Shift Lever NEU- Tral Adjustment To Start Engine with a Weak BatteryTo Adjust Carburetor Engine OIL BatteryOther Fuel SystemProblem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

191606 specifications

The Poulan 191606 is a chainsaw that makes a solid addition to any home or workshop, designed primarily for both light and medium-duty tasks. This versatile tool is ideal for homeowners, landscapers, and DIY enthusiasts who require a reliable and efficient chainsaw for various cutting needs.

One of the standout features of the Poulan 191606 is its powerful engine. Equipped with a 2-cycle engine, it delivers sufficient power to cut through logs, branches, and dense foliage with ease. The engine is not only robust but also designed to be fuel-efficient, which means users can accomplish more work without frequently stopping to refuel.

The chainsaw boasts an 18-inch bar and chain, providing an excellent balance between reach and maneuverability. The length is suitable for cutting medium-sized trees and performing precise pruning tasks while still being manageable for users of all experience levels.

Another noteworthy characteristic of the Poulan 191606 is its ease of use. The chainsaw features an automatic oiling system that ensures consistent lubrication of the bar and chain, enhancing durability and extending the life of the tool. This feature reduces maintenance chores for users, allowing them to focus more on their cutting tasks.

Moreover, the Poulan 191606 is equipped with a simple starting system that includes an easy-to-pull starter mechanism, which minimizes the effort required to get the saw running. This user-friendly design makes it accessible for both novice and experienced operators.

For added safety, the Poulan 191606 is fitted with features like a chain brake, which is crucial for preventing kickback, ensuring that users can operate the saw with peace of mind. Additionally, the handle is designed for comfort and control, providing a secure grip that can help reduce fatigue during extended use.

In summary, the Poulan 191606 combines power, efficiency, and user-friendly features, making it a commendable choice for anyone in need of a reliable chainsaw. Its durable construction, automatic oiling system, and safety features make it suitable for a range of applications, from simple yard maintenance to more extensive landscaping projects, ensuring that users can tackle their tasks effectively. Whether you're trimming branches or cutting firewood, the Poulan 191606 is designed to deliver consistent performance and reliability.
Top Page Image Contents