Poulan 188870 manual HOW to SET UP Your Tractor, Install Seat See Fig, Check Battery See Fig

Page 7

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

LOCK WASHER

ADJUSTMENT

BOLT

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

TERMINAL

TERMINAL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full “BRAKE” position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to “OFF” position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model NO. PO17542STA Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Transaxle Cooling Clean AIR ScreenEngine BeltsSpark Plugs CleaningEngine Cooling System See Fig MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust BrakeTo Attach Jumper Cables To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points When operator leaves seat Service Notes Tractor - Model Number PO17542ST PO17542STA SchematicElectrical KEY Part Description Chassis and Enclosures KEY Drive Shaft Asm Cross Tapered PMST/20 Steering Assembly 160367 Spacer Brace Axle 72110618 Optional Equipment EngineSeatlt.bolt1 Seat AssemblyWheels & Tires DecalsMower Lift Mower Deck Repair Parts Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

188870 specifications

The Poulan 188870 is a powerful and versatile chainsaw designed for both professionals and avid gardeners. Engineered for cutting through various types of wood, from hardwoods to softwoods, the Poulan 188870 showcases a combination of performance and ease of use.

One of the standout features of the Poulan 188870 is its robust engine. It incorporates a 18-inch bar and chain that delivers the necessary power for trimming branches, felling small trees, and cutting firewood. The chainsaw is powered by a reliable 50cc two-stroke engine, which is known for its efficiency and ability to handle tough tasks with minimal downtime.

The design of the Poulan 188870 includes advanced technologies aimed at improving user experience. The chainsaw is equipped with an easy-start feature, allowing for a hassle-free ignition. This saves precious time, particularly in situations where quick operation is essential. The Automatic Oiling System ensures that the chain is adequately lubricated during operation, enhancing performance and extending the lifespan of the bar and chain.

Safety is a significant consideration in the design of the Poulan 188870. It features a chain brake that activates in case of kickback, significantly reducing the risk of accidents. Additionally, with its ergonomic handle, the chainsaw is not only comfortable to hold but also minimizes vibrations, making operations smoother and reducing fatigue during prolonged use.

Another attractive characteristic of the Poulan 188870 is its lightweight construction. Weighing just over 12 pounds, it is relatively easy to maneuver, making it suitable for all-day use without causing excessive strain on the user. This is particularly beneficial for homeowners who may not have extensive experience with power tools.

In terms of maintenance, the Poulan 188870 makes it easy for users to perform routine checks and repairs. The accessible air filter and spark plug facilitate straightforward servicing, which is essential for keeping the chainsaw in optimal working condition.

Overall, the Poulan 188870 combines power, efficiency, and safety features that cater to a wide range of users. It stands out as a reliable choice for anyone in need of a dependable chainsaw for gardening or lumber work. Its balance of performance and user-friendly characteristics makes it a favorite among chainsaw enthusiasts.
Top Page Image Contents