Poulan 184314 owner manual Off

Page 28

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents PR25PH48STC Safety Rules Safe Operation Practices for Ride-On MowersSafety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP NingMaintenance Lubrication ChartService Dates General RecommendationsTractor Engine Cleaning MufflerSpark Plugs Engine OIL FilterTo Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Drive BeltTo Replace Mower Blade Drive Belt See Fig To Check BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor Model Number PR25PH48STCElectrical KEY Part Description 4152JChassis and Enclosures 28 175289X428 Grille 171875169848X428 169847X428Drive 72110614 72110612178062 Steering Assembly 180656 Wheel Steering Engine Spark Arrester137180 Kit Spark Arrestor Flat Scrn 181654Seat Assembly 182493Decals Wheels & Tires184314 184315Mower Lift Mower Deck 179479 180806184058 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Service Notes Service Notes Parts and Service
Top Page Image Contents