Poulan 187301 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 22

SERVICE AND ADJUSTMENTS

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

LEVER NEUTRAL LOCK GATE

ADJUSTMENT

BOLT

02239

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL

ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 25)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 25

TO START ENGINE WITH A WEAK BATTERY (See Fig. 26)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR DEAD BATTERY FULLY CHARGED BATTERY

FIG. 26

REPLACING BATTERY (See Figs. 27 and 28)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. PO17H42STB Safety Rules Safety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs Before Starting the EngineTo Operate Mower See Fig To Operate on HillsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Muffler CleaningSpark Plugs To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER Interlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor - Model Number PO17H42STBTractor - Model Number PO17H42STB Electrical KEY Part NO. NO. Description Tractor - Model Number PO17H42STB Chassis and Enclosures KEY Part Description Tractor - Model Number PO17H42STB Drive 17000612 Tractor - Model Number PO17H42STB Steering Assembly 17490608 Tractor - Model Number PO17H42STB Engine Optional EquipmentTractor - Model Number PO17H42STB Mower Lift Tractor - Model Number PO17H42STB Seat Assembly Tractor - Model Number PO17H42STB Decals Wheels & TiresTractor - Model Number PO17H42STB Mower Deck 165892 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXPoulan

187301 specifications

The Poulan 187301 is a specialized lawn care tool designed for both professional landscapers and enthusiastic homeowners. Known for its versatility and performance, this robust piece of equipment stands out in the crowded market of leaf blowers and lawn maintenance devices.

One of the main features of the Poulan 187301 is its powerful engine. Equipped with a reliable two-stroke engine, it delivers excellent airflow at an impressive speed, making it easy to clear leaves, debris, and grass clippings from lawns and driveways. The engine not only ensures top-tier performance but also maintains an environmentally friendly profile thanks to its efficient fuel consumption.

Weight and ergonomics play a crucial role in the usability of the Poulan 187301. Weighing slightly less than many competitors, this leaf blower is designed for extended use without causing undue strain on the operator. The comfortable handle provides a secure grip, allowing users to maneuver it easily around gardens and larger spaces.

The Poulan 187301 boasts an airspeed capacity that can reach up to 200 miles per hour, which translates into swift and effective clearing of debris. The adjustable speed settings allow users to tailor the airflow according to their specific needs, ensuring optimal performance whether dealing with wet leaves or light dust and sand.

Another key characteristic of this model is its ease of start. The Poulan 187301 incorporates advanced starting technology that minimizes the effort required to get the blower running, an essential feature for those who want to avoid frustration when starting up their equipment.

In terms of design, the Poulan 187301 is built to last, with a durable construction that can withstand the rigors of outdoor use. With minimal maintenance required, owners can expect a long lifespan from this equipment, making it a valuable investment.

Moreover, the Poulan 187301 is considered a quieter alternative compared to many other models on the market. This reduced noise level is particularly appealing for residential areas where excessive noise can be an annoyance to neighbors.

In conclusion, the Poulan 187301 combines power, efficiency, and user-friendly features, making it an excellent choice for those seeking to enhance their lawn care routine. With its advanced technologies and focus on user experience, this tool is set to meet the diverse needs of both homeowners and professionals alike.
Top Page Image Contents