Poulan 187189 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 16

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. PO1742STB Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Transaxle Cooling Clean AIR ScreenEngine BeltsSpark Plugs CleaningEngine Cooling Fins See Fig MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust BrakeTo Attach Jumper Cables To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Service Notes Tractor - Model Number PO1742STB SchematicElectrical KEY Part Description Chassis and Enclosures 179101 170 173937 DriveSteering Assembly 186737 Optional Equipment EngineSeatlt.bolt1 Seat AssemblyWheels & Tires DecalsMower Lift Mower Deck 153535 Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

187189 specifications

The Poulan 187189 is an impressive chainsaw that combines power and efficiency, making it a popular choice for both professional landscapers and homeowners alike. Renowned for its durability and performance, this model showcases a series of features that set it apart in the saturated market of outdoor power equipment.

One of the standout characteristics of the Poulan 187189 is its engine. It is equipped with a robust 18-inch guide bar and a powerful 50cc 2-cycle gas engine. This combination not only ensures powerful cutting performance but also provides the necessary torque for tackling tougher jobs, such as felling larger trees and cutting through dense wood. The chainsaw's speed is further enhanced by its automatic oiling system, which keeps the chain lubricated during operation, minimizing wear and enhancing efficiency.

The Poulan 187189 also boasts advanced technologies aimed at improving user experience. The Easy Start technology significantly reduces the effort needed to start the engine, enabling smooth and quick ignition, even in cold weather. This feature is particularly beneficial for users who may struggle with traditional starting methods, allowing them to focus on their cutting tasks rather than getting the equipment ready.

In terms of ergonomics, the 187189 is designed with user comfort in mind. It features an anti-vibration system that lessens the impact of shaking during operation, reducing fatigue during extended use. The comfortable grip handle and balanced design make it easy to maneuver, ensuring precision and control while cutting.

Durability and safety are other key elements of the Poulan 187189. The chainsaw is constructed from high-quality materials that can withstand rigorous use, while built-in safety features, such as a chain brake and low kickback chain, provide additional protection to the user.

Overall, the Poulan 187189 is a reliable chainsaw that delivers power, efficiency, and comfort. Its combination of advanced technologies and user-friendly features makes it ideal for both professionals requiring heavy-duty performance and casual users looking for an effective, easy-to-use tool for their outdoor projects. Whether for cutting firewood, trimming trees, or tackling yard work, the Poulan 187189 stands out as a versatile and dependable choice in the world of chainsaws.
Top Page Image Contents