Poulan 187009 owner manual To Remove Wheel for Repairs See Fig, Replacing Battery See Fig

Page 24

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

 

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 29

REPLACING BATTERY (See Fig. 30)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,rings,etc.

AXLE COVER

RETAINING RING

Positive terminal must be connected first to prevent sparking from accidental grounding.

SQUARE KEY (REAR WHEEL ONLY)

00663

• Lift hood to raised position.

•

Remove terminal guard.

•

Disconnect BLACK battery cable then RED battery

FIG. 28

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

 

cable and carefully remove battery from tractor.

• Install new battery with terminals in same position as

 

old battery.

•

Reinstall terminal guard.

• First connect RED battery cable to positive (+) battery

 

terminal with hex bolt and keps nut as shown. Tighten

 

securely.

• Connect BLACK grounding cable to negative (-) battery

 

terminal with remaining hex bolt and keps nut. Tighten

 

securely

•

Close terminal access doors.

•

Close hood.

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

• Connect one end of the RED cable to the POSITIVE

(+) terminal of each battery(A-B), taking care not to

short against tractor chassis.

TERMINAL ACCESS DOOR

TERMINAL GUARD

KEPS NUT

02179

HEX

BOLT

POSITIVE (RED)

CABLE

NEGATIVE (BLACK)

CABLE

•

Connect one end of the BLACK cable to the NEGATIVE

 

(-) terminal (C) of fully charged battery.

•

Connect the other end of the BLACK cable (D) to good

 

chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

FIG. 30

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PD20PH48STC Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel Gauge WheelsSeat Nose Roller MowerAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Clean AIR INTAKE/COOLING AreasMuffler Spark PlugsService and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Replace Headlight BulbTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Tractor Model Number PD20PH48STCElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Drive KEY Part NO. NO. DescriptionSteering Assembly 180656 Wheel Steering Engine Stem Tank Fuel Seat Assembly Decals Wheels & TiresMower Lift KEY Part NO. NO. Description Mower Deck 175820 Pulley Idler Flat Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

187009 specifications

The Poulan 187009 is a versatile and powerful chainsaw designed for both homeowners and professional users seeking an efficient cutting tool for various tasks. Recognized for its durability and practicality, the Poulan 187009 stands out with a range of features and characteristics that make it a popular choice among users.

One of the main features of the Poulan 187009 is its robust engine. Equipped with a 18-inch bar and powered by a 42cc two-stroke engine, this chainsaw delivers impressive performance for cutting through thick limbs, logs, and even small trees. The engine's design ensures reliable starting and smooth operation, allowing users to tackle tough jobs with confidence.

In terms of technology, the Poulan 187009 boasts a clean air filtration system, which significantly extends the life of the engine by keeping dirt and debris out. This feature enhances the chainsaw's efficiency and reduces the frequency of maintenance, making it ideal for those who prefer a low-maintenance cutting tool. Additionally, the chainsaw is designed with an easy-to-access oil reservoir, which ensures proper lubrication for optimal performance during operation.

User comfort is a key consideration in the design of the Poulan 187009. The chainsaw features a lightweight frame that not only reduces fatigue during extended use but also enhances maneuverability. The anti-vibration system included in its design minimizes hand and arm fatigue, allowing users to work longer without discomfort. The chainsaw also has an ergonomic handle, providing a secure grip for increased control and stability during cutting.

Safety is paramount when working with heavy equipment, and the Poulan 187009 includes several features to ensure user protection. It is equipped with a chain brake that stops the chain instantly in the event of kickback, a common hazard in chainsaw operation. Additionally, the chainsaw features a throttle lock-out that prevents accidental startup, enhancing overall safety while using the tool.

In summary, the Poulan 187009 combines power, efficiency, and safety features to cater to both novice and experienced users. Its strong engine, low-maintenance technologies, and user-friendly design make it an excellent choice for garden maintenance, storm cleanup, and general outdoor projects. Whether cutting firewood or tackling larger yard work tasks, the Poulan 187009 is a reliable companion that delivers consistent results.
Top Page Image Contents