Poulan 187080 To Replace Headlight Bulb, Interlocks and Relays, Replacing Battery See Figs

Page 24

SERVICE AND ADJUSTMENTS

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

SEAT PAN

 

FIG. 29

TERMINAL COVER

KEPS NUT

 

HEX BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 30

TO REPLACE HEADLIGHT BULB

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

FIG. 28

REPLACING BATTERY (See Figs. 29 and 30)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

01536

FIG. 31

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PD18H42STB Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatGauge Wheel Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Mulching Mowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER Replacing Battery See Figs To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigAcceleration Test Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PD18H42STBTractor - Model Number PD18H42STB Electrical KEY Part NO. NO. Description Tractor - Model Number PD18H42STB Chassis and Enclosures KEY Part Description Tractor - Model Number PD18H42STB Drive KEY Part NO. NO. Description Tractor - Model Number PD18H42STB Steering Assembly 180656 Wheel Steering Tractor - Model Number PD18H42STB Engine 184362 Tractor - Model Number PD18H42STB Seat Assembly KEY Part NO. no DescriptionTractor - Model Number PD18H42STB Decals Wheels & TiresTractor - Model Number PD18H42STB Mower Lift Repair Parts Tractor - Model Number PD18H42STB Mower Deck 152 153 154182032X421 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

187080 specifications

The Poulan 187080 is a versatile outdoor power tool designed to cater to the needs of both homeowner and professional landscapers. Known for its reliability and performance, this model stands out in the crowded market of string trimmers and lawn maintenance equipment.

One of the main features of the Poulan 187080 is its powerful engine. It comes equipped with a robust 25cc two-cycle engine that delivers impressive power and torque. This strength ensures efficient trimming and cutting, making it an ideal choice for tackling unruly grass, thick weeds, and taller vegetation. The engine is designed with efficiency in mind, providing ample power while maintaining a reasonable fuel consumption rate.

The design of the Poulan 187080 includes a straight shaft, which offers better reach and allows users to navigate around flower beds, fences, and hard-to-reach areas with ease. This feature is particularly useful for maintaining a clean and neat landscape. The adjustable handle provides improved control and comfort during prolonged use, reducing fatigue and allowing for precise maneuverability.

Another noteworthy characteristic of the Poulan 187080 is its Easy Start technology, which simplifies the starting process. Users will appreciate the reduced effort needed to start the engine, significantly enhancing the overall user experience. Additionally, it features a bump-feed head that allows for quick and easy line advancement, ensuring that you can keep working without frequent interruptions.

The trimmer line used with the Poulan 187080 is durable and designed to withstand the rigors of regular use. With a cutting width of 17 inches, it provides an efficient cutting path, allowing users to cover more ground in less time. This enhances productivity, especially for larger properties or extensive gardens.

Safety features include a protective guard that helps shield the user from debris while working. Overall, the Poulan 187080 embodies a combination of power, efficiency, and ease of use, making it a solid choice for those who need a reliable string trimmer for their outdoor projects. Whether you are a seasoned landscaper or a homeowner looking to maintain your lawn, the Poulan 187080 proves to be a dependable tool that meets diverse mowing and trimming needs effectively.
Top Page Image Contents