Poulan 187080 owner manual To Adjust Throttle Control Cable See Fig, To Adjust Carburetor See Fig

Page 25

SERVICE AND ADJUSTMENTS

ENGINE

Maintenance, repair, or replacement of the emission con- trol devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

Check to see if hole in throttle lever and hole in speed control bracket are aligned.

If holes are not aligned, loosen cable clamp screw and align the holes by inserting a pencil or a 1/4" drill bit through both holes.

Pull throttle cable up to remove slack and tighten cable clamp screw. Remove alignment pencil or drill bit.

TO ADJUST CARBURETOR (See Fig. 33)

The carburetor has been preset at the factory and adjustment should not be necessary.However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture. Turning the adjusting needles out (coun- terclockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: DAMAGETOTHE NEEDLES ANDTHE SEATS IN CARBURETOR MAY RESULT IF NEEDLE IS TURNED IN TOO TIGHT.

NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle with a limiter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

Be sure you have a clean air filter and the throttle control cable is adjusted properly (see above).

Start engine and allow to warm for five minutes. Make adjustments with engine running and shift/motion control lever in neutral (N) position.

Idle speed setting - With throttle control lever in slow position, engine should idle at 1750 RPM. If engine idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is attained.

Idle fuel needle setting - With throttle control lever in slow position, turn idle fuel adjustment needle in (clockwise) until engine begins to die and then turn out (counterclockwise) until engine runs rough.Turn needle to a point midway between those two positions.

Recheck idle speed. Readjust if necessary.

ACCELERATION TEST -

Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle fuel adjusting needle out (counterclockwise) 1/8 turn. Repeat test and con- tinue to adjust, if necessary, until engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.OVERSPEEDINGTHE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

CABLE

CLAMP

SCREW

SPEED CONTROL

BRACKET

THROTTLE

LEVER

FIG. 32

IDLE SPEED

ADJUSTING

SCREW

IDLE FUEL

ADJUSTING

NEEDLE

FIG. 33

25

Image 25
Contents PD18H42STB Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsGauge Wheel Slope SheetTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See a Check Battery See FigTo Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Engine OIL Filter CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor See Fig To Adjust Throttle Control Cable See FigAcceleration Test Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PD18H42STB SchematicTractor - Model Number PD18H42STB Electrical KEY Part NO. NO. Description Tractor - Model Number PD18H42STB Chassis and Enclosures KEY Part Description Tractor - Model Number PD18H42STB Drive KEY Part NO. NO. Description Tractor - Model Number PD18H42STB Steering Assembly 180656 Wheel Steering Tractor - Model Number PD18H42STB Engine 184362 KEY Part NO. no Description Tractor - Model Number PD18H42STB Seat AssemblyWheels & Tires Tractor - Model Number PD18H42STB DecalsTractor - Model Number PD18H42STB Mower Lift Repair Parts 152 153 154 Tractor - Model Number PD18H42STB Mower Deck182032X421 Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

187080 specifications

The Poulan 187080 is a versatile outdoor power tool designed to cater to the needs of both homeowner and professional landscapers. Known for its reliability and performance, this model stands out in the crowded market of string trimmers and lawn maintenance equipment.

One of the main features of the Poulan 187080 is its powerful engine. It comes equipped with a robust 25cc two-cycle engine that delivers impressive power and torque. This strength ensures efficient trimming and cutting, making it an ideal choice for tackling unruly grass, thick weeds, and taller vegetation. The engine is designed with efficiency in mind, providing ample power while maintaining a reasonable fuel consumption rate.

The design of the Poulan 187080 includes a straight shaft, which offers better reach and allows users to navigate around flower beds, fences, and hard-to-reach areas with ease. This feature is particularly useful for maintaining a clean and neat landscape. The adjustable handle provides improved control and comfort during prolonged use, reducing fatigue and allowing for precise maneuverability.

Another noteworthy characteristic of the Poulan 187080 is its Easy Start technology, which simplifies the starting process. Users will appreciate the reduced effort needed to start the engine, significantly enhancing the overall user experience. Additionally, it features a bump-feed head that allows for quick and easy line advancement, ensuring that you can keep working without frequent interruptions.

The trimmer line used with the Poulan 187080 is durable and designed to withstand the rigors of regular use. With a cutting width of 17 inches, it provides an efficient cutting path, allowing users to cover more ground in less time. This enhances productivity, especially for larger properties or extensive gardens.

Safety features include a protective guard that helps shield the user from debris while working. Overall, the Poulan 187080 embodies a combination of power, efficiency, and ease of use, making it a solid choice for those who need a reliable string trimmer for their outdoor projects. Whether you are a seasoned landscaper or a homeowner looking to maintain your lawn, the Poulan 187080 proves to be a dependable tool that meets diverse mowing and trimming needs effectively.