Poulan 183981 manual To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

 

R.H. SUSPENSION ARM

MANDREL

ENGINE

PULLEY

PULLEY

 

IDLER

RETAINER

PULLEYS

SPRING

 

 

MANDREL

 

PULLEY

FIG. 20

TO CHECK AND ADJUST BRAKE (See Fig. 21)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-1/2"

NUT “A”

 

JAM NUT

OPERATING ARM

FIG. 21

21

 

TO REPLACE MOTION DRIVE BELT (See Fig. 22)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

STATIONARY

IDLER

IDLER

CENTER SPAN

TRANSAXLE

KEEPER

PULLEY

FIG. 22

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. PO1538C IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Transport Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelTo Start Engine See Fig Mowing TipsLubrication Chart MaintenanceService Dates General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingClean AIR Screen Engine Cooling Fins See FigAIR Filter See Fig Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel ALIGN- Ment To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PO1538C, Product Number 954 56 SchematicElectrical KEY Part Description Chassis 5479J Plug Button Blk 359 Dia Choke Drive KEY Part NO. NO. Description Steering 140044X428 Wheel Steering 175131 Axle Asm Optional Equipment Kit Spark Arrestor Flat Scrn Seat Wheels & Tires DecalsMower Lift Nut Jam Hex 1/2-13 Unc Mower Deck 178515 Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

183981 specifications

The Poulan 183981 is a versatile and efficient chainsaw designed to cater to a variety of cutting tasks, making it an ideal choice for both homeowners and professionals. Known for its reliable performance, the Poulan 183981 combines innovative technology with user-friendly features to deliver exceptional results in outdoor projects.

At the heart of the Poulan 183981 is its powerful engine, which ensures high performance and durability. The engine is engineered for excellent fuel efficiency, providing users with extended run times and reduced emissions, contributing to a cleaner environment. This is particularly important for those engaged in prolonged cutting activities, as less time spent refueling means more time available for work.

One of the standout features of the Poulan 183981 is its lightweight design. Weighing less than some of its competitors, it allows for easier maneuverability and reduced fatigue during extended use. This ergonomic consideration makes the saw more accessible for novice users while still meeting the demands of seasoned professionals.

The Poulan 183981 incorporates an automatic oiling system that helps maintain the chain's lubrication during operation. This feature not only enhances the life of the chain and bar but also ensures smoother and more efficient cutting performance. With less maintenance needed, users can focus on the task at hand rather than worrying about the upkeep of their equipment.

Safety is another critical aspect of the Poulan 183981. It comes equipped with an inertia-activated chain brake, which provides an essential layer of safety by stopping the chain's movement in the event of kickback. This feature is particularly important for users who may encounter unexpected situations while cutting.

For added convenience, the Poulan 183981 features an easy-access air filter that simplifies cleaning and maintenance. This ensures optimal engine performance over time, allowing users to get the most out of their investment.

In terms of cutting capabilities, the Poulan 183981 features a high-quality cutting chain and bar that deliver precision and efficiency. Whether performing light pruning or tackling heavier jobs, this chainsaw is designed to handle a wide range of tasks with ease.

Overall, the Poulan 183981 is a well-rounded, reliable chainsaw that combines power, safety, and convenience. Its advanced technologies and practical features make it a valuable tool for anyone looking to enhance their outdoor cutting experience.
Top Page Image Contents