Poulan 180198 owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 19

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 21

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 22

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents PR1742STD II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationTable of Contents Customer Responsibilities Product SpecificationsContents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonTo SET UP Your Mower for Mulching Install Seat See FigCheck for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessLight Battery Reverse Forward FastSee Safety Rules Section Engine on Engine OFF OIL Pressure Lights onKnow Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsMulching Mowing Tips Before Each USE Lubrication ChartBefore Service Dates General RecommendationsTractor Transaxle Cooling Clean AIR ScreenEngine BeltsEngine OIL Filter CleaningMuffler Spark PlugsTo Remove Mower See Fig To Install Mower See FigFRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigInterlocks and Relays Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbTo Adjust Carburetor To Adjust Throttle Control Cable See FigCylinders OtherFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR1742STD SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Wheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift Tractor Model Number PR1742STD159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policywarranty Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

180198 specifications

The Poulan 180198 is a robust and versatile tool designed for both professional landscapers and homeowners alike. This chainsaw stands out in the market due to its reliable performance and user-friendly features. It's engineered to tackle a wide range of cutting tasks, from trimming branches to felling small trees, making it an essential equipment for anyone serious about yard maintenance.

One of the main features of the Poulan 180198 is its powerful engine. The chainsaw is equipped with a 18-inch bar and chain, allowing for long reach and effective cutting without overly stretching the user’s capabilities. The saw is powered by a dependable two-stroke engine, providing sufficient power and efficiency to handle various cutting needs. The engine operates smoothly while minimizing fuel consumption, which not only enhances the operational costs but also supports a more environmentally friendly approach.

Another notable technology in the Poulan 180198 is its Easy Start system, which significantly reduces the effort required to start the chainsaw. This feature is beneficial for both seasoned professionals and occasional users, as it eliminates the frustration often associated with starting power tools. Additionally, the chainsaw is designed with vibration dampening technology which contributes to user comfort. By minimizing vibrations, the tool reduces fatigue during prolonged use, making it ideal for more extensive projects.

Safety is a crucial consideration in any chainsaw, and the Poulan 180198 does not disappoint. It includes essential safety features, such as a chain brake that halts chain movement in the event of a kickback, and an automatic oiler that ensures the chain remains lubricated for optimal performance. The ergonomic design of the handle provides a secure grip, enhancing control while allowing for precise cuts.

The Poulan 180198 is built for durability, with a sturdy construction that can withstand regular use in challenging environments. Its lightweight design makes it easier to maneuver, reducing strain on the user while increasing productivity.

In summary, the Poulan 180198 combines power, efficiency, and safety into a chainsaw that meets the demands of any cutting job. Its advanced technologies and robust features make it a reliable choice for users looking for a high-performing yet manageable tool for their outdoor projects.
Top Page Image Contents