Poulan 180198 Transaxle Gear Shift Lever Neutral Adjustment See Fig, Front Wheel TOE-IN/CAMBER

Page 21

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

LOCK GATE

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the CUSTOMER RESPON- SIBILITIES section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PR1742STD Safe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsContents of Hardware Pack HOW to SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidTo SET UP Your Mower for Mulching Install Seat See FigCheck Tire Pressure To Convert to Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL BeltsSee Safety Rules Section Battery Reverse Forward FastEngine on Engine OFF OIL Pressure Lights on LightKnow Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigMulching Mowing Tips Before Service Dates Lubrication ChartGeneral Recommendations Before Each USETractor Engine Clean AIR ScreenBelts Transaxle CoolingMuffler CleaningSpark Plugs Engine OIL FilterTo Remove Mower See Fig To Install Mower See FigFRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Gear Shift Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigFuel System OtherEngine OIL CylindersTroubleshooting Points OFF Tractor - Model Number PR1742STD SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Wheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift Tractor Model Number PR1742STD159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policywarranty Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

180198 specifications

The Poulan 180198 is a robust and versatile tool designed for both professional landscapers and homeowners alike. This chainsaw stands out in the market due to its reliable performance and user-friendly features. It's engineered to tackle a wide range of cutting tasks, from trimming branches to felling small trees, making it an essential equipment for anyone serious about yard maintenance.

One of the main features of the Poulan 180198 is its powerful engine. The chainsaw is equipped with a 18-inch bar and chain, allowing for long reach and effective cutting without overly stretching the user’s capabilities. The saw is powered by a dependable two-stroke engine, providing sufficient power and efficiency to handle various cutting needs. The engine operates smoothly while minimizing fuel consumption, which not only enhances the operational costs but also supports a more environmentally friendly approach.

Another notable technology in the Poulan 180198 is its Easy Start system, which significantly reduces the effort required to start the chainsaw. This feature is beneficial for both seasoned professionals and occasional users, as it eliminates the frustration often associated with starting power tools. Additionally, the chainsaw is designed with vibration dampening technology which contributes to user comfort. By minimizing vibrations, the tool reduces fatigue during prolonged use, making it ideal for more extensive projects.

Safety is a crucial consideration in any chainsaw, and the Poulan 180198 does not disappoint. It includes essential safety features, such as a chain brake that halts chain movement in the event of a kickback, and an automatic oiler that ensures the chain remains lubricated for optimal performance. The ergonomic design of the handle provides a secure grip, enhancing control while allowing for precise cuts.

The Poulan 180198 is built for durability, with a sturdy construction that can withstand regular use in challenging environments. Its lightweight design makes it easier to maneuver, reducing strain on the user while increasing productivity.

In summary, the Poulan 180198 combines power, efficiency, and safety into a chainsaw that meets the demands of any cutting job. Its advanced technologies and robust features make it a reliable choice for users looking for a high-performing yet manageable tool for their outdoor projects.
Top Page Image Contents