Poulan PPB200 LE Carburetor Adjustments, Seasonal Storage, Fuel System, Engine, Other

Page 9

NOTE: Do not attempt to clean the spark ar- resting screen.

1.Loosen and remove the 2 screws from the muffler cover. Remove the muffler cover.

2.Loosen and remove both screws from the exhaust diverter.

3.Remove the exhaust diverter and spark arresting screen.

4 Install new spark arresting screen.

5.Reinstall exhaust diverter and both screws. Tighten screws securely.

6.Reinstall muffler cover and 2 screws. Tighten securely.

NOTE: If any part of the muffler is cracked, broken or damaged, we recommend that the muffler be replaced.

CARBURETOR ADJUSTMENTS

There is no screw for idle adjustment on your blower. The throttle lever is used to control engine speed. The throttle lever can be placed in one of four positions: STOP, IDLE

or , FULL THROTTLE or , and one intermittent position. If your engine will not run properly or you require further assistance, contact an authorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy stor-

age.

SStore in a clean dry area.

SLightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

S Replace your gasoline can if it starts to rust.

-- 9 --

Image 9
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Know Your UnitHandle Fuel with CAUTION, IT is Highly Flammable Operate Your Unit SafelyBlower Tube Assembly Vacuum BAG AssemblyMaintain Your Unit Properly HOW to Convert Unit from Vacuum USE to Blower USE Vacuum Tube AssemblyKnow Your Blower Shoulder Strap AdjustmentThrottle Lever Primer ButtonOperating Tips Operating PositionBefore Starting Engine Fueling Engine To Stop the EngineStarting a Warm Engine Starting a Cold EngineStarting a Flooded Engine General RecommendationsClean AIR Filter Inspect and Clean Unit and DecalsCheck Muffler Mounting Screws Replace Spark PlugSeasonal Storage Carburetor AdjustmentsFuel System EngineAdjustment Crankshaft seals worn Troubleshooting Table Cause RemedyAdjustment Carbon build upTions The U.S. Environmental Protection Electrolux Home PRODUCTS, INC