Poulan S1634 LE, S1838 LE Tree Felling Techniques, Felling Large Trees, Direction of Fall

Page 11
Opening of felling cut

SAllow the chain to cut for you. Exert only light downward pressure. If you force

the cut, damage to the bar, chain, or en- gine can result.

SRelease the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load, unneces- sary wear can occur to the chain, bar, and engine. It is recommended that the engine not be operated for lon- ger than 30 seconds at full throttle.

STo avoid losing control when cut is com- plete, do not put pressure on saw at end of cut.

S Stop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near build- ings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree makes contact with any utility line, the utility company should be notified immediately.

SCarefully plan your sawing operation in ad- vance.

SClear the work area. You needa clear area all around the tree so you can have secure

footing.

Plan a clear retreat path

Direction of Fall

45_

FELLING LARGE TREES

(6 inches in diameter or larger)

The notch method is used to fell large trees. A notch is cut on the side of the treein the de- sired direction of fall. After a felling cut is made on the opposite side of tree, the tree will tend to fall into the notch.

NOTE: If the tree has large buttress roots, remove them before making the notch. If using saw to remove buttress roots, keep saw chain from contacting ground to prevent dulling of the chain.

NOTCH CUT AND FELLING THE TREE

SMake notch cut by cutting the top of the notch first. Cut through 1/3 of the diameter of the tree. Next complete the notch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut remove the notch of wood from the tree.

Final (felling) cut here. 2 in- ches above center of notch.

SThe chain saw operator should keep on

the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled.

SStudy the natural conditions that can cause

the tree to fall in a particular direction. Natural conditions that can cause a tree to fall in a particular direction include:

SThe wind direction and speed.

S The lean of the tree. The lean of a tree might not be apparent due to uneven or sloping terrain. Use a plumb or level to de-

First cut

Notch

Second cut

Hinge

termine the direction of tree lean.

SWeight and branches on one side. S Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted, it can snap and fall toward the operator. Check for broken or dead branches which can fall on you while cutting.

Make sure there is enough room for the tree to fall. Maintain a distance of 2-1/2tree lengths from the nearest person or other ob- jects. Engine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, sta- ples, and wire from the tree wherecuts areto be made.

Plan a clear retreat path to the rear and diag- onal to the line of fall.

S After removing the wood from the notch, make the felling cut on the opposite side of the notch. This is done by making a cut about two inches higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form a hinge. This hinge will help prevent the tree from falling in the wrong direction.

Hinge holds tree on stump and helps control fall

Closing of notch

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 530164161 6/26/03 Manual de Instrucciones Manuel d’InstructionsStarting or operating the chain saw Plan AheadTions before attempting to use the unit Hearing Afety Hat Prote ction Eye Protection Snug FittingKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionMaintain Control Kickback Safety FeaturesReduce the Chance of Kickback 952044418 Chain Brake and CKA Angle952044370 952051534Cha in Brake Nuts Bar Tool Inside view Chain Brake Adjustment located on Chain BrakeAttachingthe BAR & CHAINIf not Chain Tension Adjusting the tensionChecking the tension Throttle LOCK--OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerCation Always stop the engine before removing the oil cap Fueling EngineBAR and Chain Lubrication Important Points to RememberInertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beDirection of Fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for Bucking1st Cut 2nd Cut Limbing and Pruning Important PointsLimbing PruningInspect Muffler and Spark Arresting Screen Cleaning the Spark ARREST- ING ScreenCarburetor Adjustment AIR FilterIgnition Timing BAR MaintenanceNeed Service PART? Chain SharpeningTroubleshooting Table Cause Remedy Related Parts Any Electrolux HOW to File a Claim If you have anyTions The U.S. Environmental Protection Intermediate 125 hours Extended 300 hours

S1634 LE, S1838 LE specifications

Poulan has long been recognized as a reliable name in the outdoor power equipment industry, and their chainsaws, particularly the Poulan S1634 LE and S1838 LE models, are prime examples of this reputation.

The Poulan S1634 LE is designed for homeowners seeking a lightweight and efficient chainsaw for various cutting tasks. With a 16-inch cutting bar, it is well-suited for trimming branches, tackling small to medium-sized trees, and firewood preparation. The chainsaw is powered by a 33cc 2-cycle engine that provides ample power while remaining easy to handle. One of the standout features of the S1634 LE is its lightweight construction, weighing in at just over 10 pounds, allowing for comfortable maneuverability, especially during extended use.

The S1838 LE model takes a step up in terms of power and capability. With an 18-inch cutting bar and a more robust 42cc engine, this chainsaw can handle larger tasks with ease. The increased bar length allows users to cut through thicker trees and larger branches without excessive effort. Like the S1634 LE, the S1838 LE is designed with user comfort in mind, incorporating features such as an anti-vibration system that reduces user fatigue and a cushioned handle for a secure grip.

Both models come equipped with reliable safety features, including a chain brake that engages automatically in the event of kickback, providing additional peace of mind during operation. The easy-access air filter and tool-free chain tensioning system simplify maintenance and enhance overall usability, allowing users to keep their equipment in optimal condition with minimal hassle.

Furthermore, both chainsaws feature Poulan's reliable start technology, which utilizes a primer bulb and choke for quicker starts, minimizing downtime. The fuel-efficient engines of both models also help to reduce running costs, making them an economical choice for homeowners and occasional users.

In summary, the Poulan S1634 LE and S1838 LE chainsaws are excellent choices for anyone looking for a dependable, user-friendly chainsaw for various cutting tasks. With powerful engines, ergonomic designs, and essential safety features, these models deliver the performance and reliability that Poulan is known for, making them suitable for both novice and experienced users alike. Whether for yard maintenance or occasional lumberjack tasks, these chainsaws provide an impressive blend of power, efficiency, and user comfort.
Top Page Image Contents