Poulan S1634 LE, S1838 LE BAR Maintenance, Chain Sharpening, Ignition Timing, Spark Plug, Storage

Page 15

STurn idle speed screw (T) clockwise to in- crease engine speed.

STurn idle speed screw (T) counterclock- wise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call 1--800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced throughthe cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi-

tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from

saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-

ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch socket wrench. Spark plug gap should be 0.025 inches.

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

Cylinder

Spark

Cover

 

Plug Boot

 

Spark

Plug

STORAGE

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Storeunit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children.

SBefore storing, drain all fuel from the unit. Start engine and allow to run until it stops.

SClean the unit before storing. Pay particu- lar attention to the air intake area, keeping

it free of debris. Use a mild detergent and sponge to clean the plastic surfaces.

SDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an openflame from hot water heaters, electric

motors or switches, furnaces, etc.

SStore in a dry area out of the reach of chil- dren.

CAUTION: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.

NEED ASSISTANCE?

Call 1--800--554--6723.

NEED SERVICE PART?

Contact your dealer or place of purchase.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 530164161 6/26/03 Manual de Instrucciones Manuel d’InstructionsStarting or operating the chain saw Plan AheadTions before attempting to use the unit Hearing Afety Hat Prote ction Eye Protection Snug FittingKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionKickback Safety Features Reduce the Chance of KickbackMaintain Control 952044418 Chain Brake and CKA Angle952044370 952051534Inside view Chain Brake Adjustment located on Chain Brake Attachingthe BAR & CHAINIf notCha in Brake Nuts Bar Tool Adjusting the tension Checking the tensionChain Tension Throttle LOCK--OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerCation Always stop the engine before removing the oil cap Fueling EngineBAR and Chain Lubrication Important Points to RememberInertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beDirection of Fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for Bucking1st Cut 2nd Cut Limbing and Pruning Important PointsLimbing PruningInspect Muffler and Spark Arresting Screen Cleaning the Spark ARREST- ING ScreenCarburetor Adjustment AIR FilterIgnition Timing BAR MaintenanceNeed Service PART? Chain SharpeningTroubleshooting Table Cause Remedy HOW to File a Claim If you have any Tions The U.S. Environmental ProtectionRelated Parts Any Electrolux Intermediate 125 hours Extended 300 hours

S1634 LE, S1838 LE specifications

Poulan has long been recognized as a reliable name in the outdoor power equipment industry, and their chainsaws, particularly the Poulan S1634 LE and S1838 LE models, are prime examples of this reputation.

The Poulan S1634 LE is designed for homeowners seeking a lightweight and efficient chainsaw for various cutting tasks. With a 16-inch cutting bar, it is well-suited for trimming branches, tackling small to medium-sized trees, and firewood preparation. The chainsaw is powered by a 33cc 2-cycle engine that provides ample power while remaining easy to handle. One of the standout features of the S1634 LE is its lightweight construction, weighing in at just over 10 pounds, allowing for comfortable maneuverability, especially during extended use.

The S1838 LE model takes a step up in terms of power and capability. With an 18-inch cutting bar and a more robust 42cc engine, this chainsaw can handle larger tasks with ease. The increased bar length allows users to cut through thicker trees and larger branches without excessive effort. Like the S1634 LE, the S1838 LE is designed with user comfort in mind, incorporating features such as an anti-vibration system that reduces user fatigue and a cushioned handle for a secure grip.

Both models come equipped with reliable safety features, including a chain brake that engages automatically in the event of kickback, providing additional peace of mind during operation. The easy-access air filter and tool-free chain tensioning system simplify maintenance and enhance overall usability, allowing users to keep their equipment in optimal condition with minimal hassle.

Furthermore, both chainsaws feature Poulan's reliable start technology, which utilizes a primer bulb and choke for quicker starts, minimizing downtime. The fuel-efficient engines of both models also help to reduce running costs, making them an economical choice for homeowners and occasional users.

In summary, the Poulan S1634 LE and S1838 LE chainsaws are excellent choices for anyone looking for a dependable, user-friendly chainsaw for various cutting tasks. With powerful engines, ergonomic designs, and essential safety features, these models deliver the performance and reliability that Poulan is known for, making them suitable for both novice and experienced users alike. Whether for yard maintenance or occasional lumberjack tasks, these chainsaws provide an impressive blend of power, efficiency, and user comfort.
Top Page Image Contents