Poulan PR25PH48STB owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 20

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION:Bladesaresharp.Protectyour hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

MANDREL

“B”“B”

FIG. 22

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

 

TRUNNION

NUT “D”

 

FRONT

NUT “C”

PLATE

 

ASSEMBLY

 

FIG. 23

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PR25PH48STB Safe Operation Practices for Ride-On Mowers Safety RulesSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Battery Reverse Forward FastKnow Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionService Dates Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Muffler CleaningSpark Plugs Engine OIL FilterService and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Adjust Brake See Fig To Replace Mower Drive BeltTo Replace Mower Blade Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Remove Hood and Grill Assembly See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Schematic Tractor Model Number PR25PH48STBNON-REMOVABLE Removable Connections Connections Electrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Repair PartsTransaxle Order parts from Steering Assembly 180657 Engine Seat Assembly Wheels & Tires DecalsMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Service Notes Service Notes Parts and Service

PR25PH48STB specifications

The Poulan PR25PH48STB is a versatile and powerful tool designed to tackle various yard maintenance tasks with ease. Ideal for both homeowners and professional landscapers, this string trimmer combines user-friendly features and advanced technology to ensure efficient performance.

Equipped with a robust 25cc 2-stroke engine, the PR25PH48STB delivers ample power for clearing through tough grasses and weeds. This lightweight engine contributes to the overall maneuverability of the trimmer, allowing users to navigate around obstacles without fatigue during extended use. The high-performance engine is not only powerful but also designed to be fuel-efficient, helping users to save on fuel costs while minimizing their environmental impact.

One of the standout features of the Poulan PR25PH48STB is its pivoting head, which allows for easy transitions between trimming and edging tasks. This unique feature facilitates a smooth operation, making it simple to achieve a clean and professional finish around gardens, driveways, and patios. Additionally, the adjustable handle provides comfort and control, enabling users to change their grip position to suit their height and working style.

The dual-line capability of the PR25PH48STB enhances its cutting efficiency. By using two lines simultaneously, the trimmer can cover a larger area and reduce the time required to complete the job. The Easy Reload string head makes it simple to replace the cutting line, minimizing downtime and keeping users focused on the task at hand.

The trimmer also incorporates anti-vibration technology, which significantly reduces fatigue during prolonged use. This makes it an excellent choice for those who need to tackle large areas or complete challenging tasks without experiencing discomfort. Additionally, the lightweight design contributes to the ease of use and overall user experience.

For enhanced convenience, the PR25PH48STB features a straight shaft design, which provides better reach under bushes and around trees, ensuring gardeners can maintain their yards more effectively. This design also reduces the chance of the user having to bend or strain their back while working.

Overall, the Poulan PR25PH48STB stands out as a reliable and efficient trimmer that combines power, versatility, and user-friendly features. With its advanced technologies and robust design, it’s an ideal solution for anyone looking to maintain a pristine outdoor space effortlessly.
Top Page Image Contents