Poulan PR20PH42STA owner manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 14

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities section in this manual.

ADD GASOLINE

•Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm- up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PR20PH42STA Safe Operation Practices for Ride-On Mowers Safety Rules Table of Contents Seat Unassembled PartsSteering Wheel KeysHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingInstall Mulcher Plate See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemBattery Reverse Forward Fast OperationKnow Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMulching Mowing Tips Purge TransmissionMowing Tips Customer Responsibilities Service DatesLubrication Chart General RecommendationsBrake Operation Blade Care BatteryTractor TiresEngine Spark Plugs CleaningMuffler Engine OIL FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Adjust Steering Wheel Alignment To Adjust Brake See FigTransmission REMOVAL/REPLACEMENT To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Attach Jumper CablesTo Replace Fuse To Replace Headlight BulbInterlocks and Relays To Adjust Carburetor Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Wiring Insulated Clips PTO Switch SchematicIgnition Switch Tractor Model Number PR20PH42STAElectrical KEY Part Description 175688Chassis and Enclosures Bracket Fender Repair Parts DriveTransaxle Order parts from Steering Assembly 175118 Bolt Shoulder 7/16-20 Unc 175553 Clip KEY Part NO. NO. Description EngineOptional Equipment Seat Assembly Decals Wheels & TiresMower Lift Mower Deck Bar Adjusting Gauge Wheel Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PR20PH42STA specifications

The Poulan PR20PH42STA is a robust lawn mower that has garnered attention for its impressive performance and user-friendly features. Designed for both residential and light commercial use, this mower stands out in the competitive market for its durability and efficiency.

One of the standout features of the Poulan PR20PH42STA is its powerful engine. Equipped with a reliable 20 horsepower engine, it provides ample power to tackle various mowing conditions, ensuring a clean and even cut across diverse terrains. The mower’s cutting deck measures 42 inches, allowing it to cover a substantial amount of ground in each pass, which is ideal for medium to larger-sized yards.

The PR20PH42STA also employs a hydrostatic transmission system, which offers seamless gear shifts and an easy-to-control speed. This feature is particularly beneficial for users seeking a mowing experience that does not require frequent stopping to adjust speeds, making it ideal for navigating around obstacles such as trees and flower beds.

Another impressive aspect of this mower is its adjustable cutting height. With various height settings, users can customize the lawn's finish to their preference, from a close trim to a higher cut that promotes grass health. This versatility allows homeowners to adapt to seasonal conditions and grass types, ensuring an aesthetically appealing lawn throughout the year.

In terms of design, the Poulan PR20PH42STA boasts a comfortable and ergonomic seating arrangement that enables users to mow for extended periods without fatigue. The easy-to-reach controls contribute to a user-friendly interface, making it accessible to both seasoned users and those new to lawn care.

The mower also features a mulching capability, which not only enhances the health of the lawn by returning nutrients but also eliminates the need for bagging clippings. Users can expect a neat finish while promoting an eco-friendly approach to lawn maintenance.

Durability is another key characteristic of the Poulan PR20PH42STA. Constructed with high-quality materials, it is designed to withstand the rigors of regular use, ensuring longevity and reliability.

In conclusion, the Poulan PR20PH42STA combines power, versatility, and comfort, making it an excellent choice for homeowners looking to maintain their lawns efficiently. With its array of features and user-friendly design, this mower is well-equipped to handle the demands of lawn care, ensuring a healthy and beautifully manicured landscape.
Top Page Image Contents