Poulan PR20PH42STA owner manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 18 and 19)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER TO

OF MOWER TO

GROUND

GROUND

 

A

A

 

GROUND

 

LINE

FIG. 18

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 19

FRONT-TO-BACK ADJUSTMENT (See Figs. 20 and 21)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”“D”

FIG. 20

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “E”

NUT “F”

FRONT

LINKSTRUNNION

FIG. 21

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 22)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PR20PH42STA Safe Operation Practices for Ride-On Mowers Safety Rules Table of Contents Steering Wheel Unassembled PartsSeat KeysTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching Install Mulcher Plate See FigTo Convert to Bagging or Discharging Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Battery Reverse Forward FastKnow Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsMulching Mowing Tips Lubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Blade Care BatteryBrake Operation TiresEngine Muffler CleaningSpark Plugs Engine OIL FilterService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing To Replace Mower Blade Drive Belt See FigBelt Removal Transmission REMOVAL/REPLACEMENT To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Ignition Switch SchematicWiring Insulated Clips PTO Switch Tractor Model Number PR20PH42STAElectrical 175688 KEY Part DescriptionChassis and Enclosures Bracket Fender Drive Repair PartsTransaxle Order parts from Steering Assembly 175118 Bolt Shoulder 7/16-20 Unc 175553 Clip Engine Optional EquipmentKEY Part NO. NO. Description Seat Assembly Wheels & Tires DecalsMower Lift Mower Deck Bar Adjusting Gauge Wheel Service Notes Service Notes Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PR20PH42STA specifications

The Poulan PR20PH42STA is a robust lawn mower that has garnered attention for its impressive performance and user-friendly features. Designed for both residential and light commercial use, this mower stands out in the competitive market for its durability and efficiency.

One of the standout features of the Poulan PR20PH42STA is its powerful engine. Equipped with a reliable 20 horsepower engine, it provides ample power to tackle various mowing conditions, ensuring a clean and even cut across diverse terrains. The mower’s cutting deck measures 42 inches, allowing it to cover a substantial amount of ground in each pass, which is ideal for medium to larger-sized yards.

The PR20PH42STA also employs a hydrostatic transmission system, which offers seamless gear shifts and an easy-to-control speed. This feature is particularly beneficial for users seeking a mowing experience that does not require frequent stopping to adjust speeds, making it ideal for navigating around obstacles such as trees and flower beds.

Another impressive aspect of this mower is its adjustable cutting height. With various height settings, users can customize the lawn's finish to their preference, from a close trim to a higher cut that promotes grass health. This versatility allows homeowners to adapt to seasonal conditions and grass types, ensuring an aesthetically appealing lawn throughout the year.

In terms of design, the Poulan PR20PH42STA boasts a comfortable and ergonomic seating arrangement that enables users to mow for extended periods without fatigue. The easy-to-reach controls contribute to a user-friendly interface, making it accessible to both seasoned users and those new to lawn care.

The mower also features a mulching capability, which not only enhances the health of the lawn by returning nutrients but also eliminates the need for bagging clippings. Users can expect a neat finish while promoting an eco-friendly approach to lawn maintenance.

Durability is another key characteristic of the Poulan PR20PH42STA. Constructed with high-quality materials, it is designed to withstand the rigors of regular use, ensuring longevity and reliability.

In conclusion, the Poulan PR20PH42STA combines power, versatility, and comfort, making it an excellent choice for homeowners looking to maintain their lawns efficiently. With its array of features and user-friendly design, this mower is well-equipped to handle the demands of lawn care, ensuring a healthy and beautifully manicured landscape.
Top Page Image Contents