Poulan PR18542STC Replacing Battery See Figs, To Replace Headlight Bulb, Interlocks and Relays

Page 22

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Figs. 26 and 27)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position and open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

•Close battery box door.

SEAT PAN

BATTERY

BOX DOOR

FIG. 26

KEPS

NUT

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 27

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 28

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PR18542STC Safety Rules Safe Operation Practices for RIDE-ON MowersTable of Contents Product Specifications Customer ResponsibilitiesSeat Unassembled HardwareSteering Wheel Keys Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsMulching Mowing Tips Customer Responsibilities General Recommendations Lubrication ChartBefore Each USE Tractor Engine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor - Model Number PR18542STCElectrical 2122175141 175158175566 121433XChassis and Enclosures 30 169470X428 Fender 174619176554 174930Drive 72140608 175410175765 73900600Steering Assembly 175146 175121177876 175118Seat Assembly 174894Decals Wheels and TiresEngine Optional Equipment Spark ArresterEngine Mower Deck 17060514 71081010174493 165890X421Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Sighting GuideParts and Service
Top Page Image Contents