Poulan PP3816 AV, PP4218 AV instruction manual Storage

Page 16

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY section.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase

engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp

object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/Weed Eater 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel sta- bilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PP3816 AV / PP4218 AV For Occasional Use Only 12/8/05Identification of Symbols Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Chain Brake and CKA Angle WE do not REPResent and YOU should not AS Sume That the Chain Brake willAssembly Adjusting Screw Tensioning RackAttaching the BAR & Chain If not CuttersChain Tension Adjusting the tensionChecking the tension Operation Before Starting Engine Fueling Engine BAR and Chain LubricationImportant Points to Remember Cation Always stop the engine before removing the oil capStarting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points LimbingPruning ING Without a SupportService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill withTions The U.S. Environmental Protection Electrolux Home PRODUCTS, INCConsequential Damages Electro

PP3816 AV, PP4218 AV, PP4218 AV specifications

The Poulan PP4218 AV, PP3816 AV, and PP4218 AV chainsaws are renowned for their efficiency, power, and innovative features, making them reliable choices for both amateur and professional users. These models are designed to cater to various cutting needs, from trimming branches to felling larger trees.

The Poulan PP4218 AV is equipped with an 18-inch bar and a powerful 42cc engine, offering a commendable balance of weight and performance. One of its key features is the anti-vibration system, which significantly reduces operator fatigue during extended use. The chainsaw also boasts a tool-less chain tensioning system, making it easy to adjust the chain without needing additional tools. This is especially useful for ensuring optimal cutting performance and safety.

The PP3816 AV, on the other hand, offers a slightly smaller package with a 16-inch bar and a 38cc engine. This model is designed for users who require a lightweight chainsaw for smaller tasks such as pruning and lightweight cutting. It too features the anti-vibration technology, enhancing comfort during operation. The quick start system allows for easier startups, making it accessible to users of all experience levels. Its compact design also provides excellent maneuverability, making it perfect for tight spaces.

The PP4218 AV is very similar to the original PP4218 AV, yet it incorporates further refinements in performance and ergonomics. It remains powerful with its 42cc engine and 18-inch bar but includes enhanced features such as a more efficient air filtration system. This improvement not only extends the life of the engine by keeping it cleaner but also ensures optimal performance even in dusty conditions. Additionally, it maintains the easy access to controls and the comfortable grip design that Poulan is known for, making it a favorite among homeowners and professionals alike.

All three models utilize Poulan's exclusive OxyPower technology, which delivers more power while reducing emissions. This commitment to environmentally friendly technology ensures that users can operate these chainsaws with a focus on sustainability.

In summary, whether you choose the PP4218 AV, PP3816 AV, or stick with the original PP4218 AV, each chainsaw combines power, convenience, and advanced technologies, making them excellent tools for tackling a wide range of cutting tasks.
Top Page Image Contents