Poulan PP3816 AV, PP4218 AV Chain Tension, Checking the tension, Adjusting the tension

Page 7

6.Place chain over and behind the clutch retainer, fitting the drive links in the clutch drum sprocket.

7.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

8.Fit chain drive links into bar groove.

9.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

10.Hold guide bar against the saw frame and install clutch cover.

11.Install bar nuts and finger tighten only. Once the chain is tensioned, you will need to tighten bar nuts.

CHAIN TENSION

(Including units with chain already installed)

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move chain around guide bar. If the chain does not rotate, it is too tight. If the chain is too loose, it will sag below the bar.

Guide

 

Bar

 

Chain Adjustment

Bar Nuts

Tool

(Bar Tool)

 

Adjusting the tension:

Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

An adjusting screw (located on the guide bar) is used to adjust the tension of the chain (see illustration).

1.Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Guide bar

Adjusting

Screw

2.Using bar tool, roll chain around guide bar to ensure all links are in bar groove.

3.Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn ad- justing screw clockwise until sag does not exist.

4.While lifting tip of guide bar, tighten bar nuts securely with the bar tool.

Bar Nuts

5.Use the screwdriver end of the bar tool to move chain around guide bar.

6.If chain does not rotate, it is too tight. Slightly loosen bar nuts and loosen chain by turning the adjusting screw. Retighten bar nuts.

7.If chain is too loose, it will sag below the guide bar. DO NOT operate the saw if the chain is loose.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 12/8/05 PP3816 AV / PP4218 AV For Occasional Use OnlyPlan Ahead Identification of SymbolsKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Sume That the Chain Brake will Chain Brake and CKA AngleWE do not REP Resent and YOU should not ASCutters AssemblyAdjusting Screw Tensioning Rack Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation Cation Always stop the engine before removing the oil cap Before Starting Engine Fueling EngineBAR and Chain Lubrication Important Points to RememberInertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beNotch CUT and Felling the Tree Operating TipsTree Felling Techniques Felling Large TreesTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Important PointsING Without a Support Limbing and Pruning Important PointsLimbing PruningService Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Cleaning the Spark ARREST- ING ScreenStorage Empty fuel tank and refill with Load Adjustment EngineEngine OtherElectrolux Home PRODUCTS, INC Tions The U.S. Environmental ProtectionConsequential Damages Electro

PP3816 AV, PP4218 AV, PP4218 AV specifications

The Poulan PP4218 AV, PP3816 AV, and PP4218 AV chainsaws are renowned for their efficiency, power, and innovative features, making them reliable choices for both amateur and professional users. These models are designed to cater to various cutting needs, from trimming branches to felling larger trees.

The Poulan PP4218 AV is equipped with an 18-inch bar and a powerful 42cc engine, offering a commendable balance of weight and performance. One of its key features is the anti-vibration system, which significantly reduces operator fatigue during extended use. The chainsaw also boasts a tool-less chain tensioning system, making it easy to adjust the chain without needing additional tools. This is especially useful for ensuring optimal cutting performance and safety.

The PP3816 AV, on the other hand, offers a slightly smaller package with a 16-inch bar and a 38cc engine. This model is designed for users who require a lightweight chainsaw for smaller tasks such as pruning and lightweight cutting. It too features the anti-vibration technology, enhancing comfort during operation. The quick start system allows for easier startups, making it accessible to users of all experience levels. Its compact design also provides excellent maneuverability, making it perfect for tight spaces.

The PP4218 AV is very similar to the original PP4218 AV, yet it incorporates further refinements in performance and ergonomics. It remains powerful with its 42cc engine and 18-inch bar but includes enhanced features such as a more efficient air filtration system. This improvement not only extends the life of the engine by keeping it cleaner but also ensures optimal performance even in dusty conditions. Additionally, it maintains the easy access to controls and the comfortable grip design that Poulan is known for, making it a favorite among homeowners and professionals alike.

All three models utilize Poulan's exclusive OxyPower technology, which delivers more power while reducing emissions. This commitment to environmentally friendly technology ensures that users can operate these chainsaws with a focus on sustainability.

In summary, whether you choose the PP4218 AV, PP3816 AV, or stick with the original PP4218 AV, each chainsaw combines power, convenience, and advanced technologies, making them excellent tools for tackling a wide range of cutting tasks.
Top Page Image Contents