Poulan P4018AV BH, P4018WT, P4018 P4018WM Important Points to Remember, Starting a Warm Engine

Page 10

Use only 15-- 18(40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020(0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

10

Image 10
Contents Manual de Instrucciones Manuel d’Instructions 545137250 11/30/06Plan Ahead Starting ReminderTions found in this manual Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Assembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Primer Bulb Throttle LOCK-OUT Chain BrakeCHOKE/FAST Idle Lever Before Starting EngineDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Right Foot Through Rear HandleOperating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingService Cleaning the Spark ARREST- ING Screen Inspect and Clean Unit and DecalsClean AIR Filter Check Fuel Mixture LevelStorage Engine Load Adjustment EngineOther Limited Warranty Ligations The U.S. EnvironmentalNANCE, Replacement and Repair
Related manuals
Manual 4 pages 35.01 Kb

P4018 P4018WM, P3516PR, P4018WT, P3314WS, P3818AV P4018AV specifications

The Poulan brand has established itself as a reliable name in outdoor power equipment, particularly with its diverse range of chainsaws designed for various cutting needs. The models P4018AV BH, P3314WSA, P3416, P3818AV, P4018AV, P3314WS, and P4018WT offer users cutting-edge technology and features tailored for efficiency, durability, and ease of use.

The P4018AV BH is a standout model featuring a powerful 40cc, 2-cycle engine that delivers robust cutting performance. Equipped with an anti-vibe handle system, it minimizes user fatigue during extended use. Its 18-inch cutting bar increases the cutting capacity, making it suitable for larger trees and branches. The tool-less chain tensioning system allows for quick adjustments, ensuring optimal performance without the need for additional tools.

The P3314WSA offers a 33cc engine, making it a lightweight option for casual users. This model is particularly suitable for homeowners and novice users who require a dependable chainsaw for light to moderate cutting tasks. The 14-inch guide bar provides excellent maneuverability, while the automatic oiler ensures continuous lubrication of the chain for smoother operation.

Moving to the P3416, this chainsaw is well-balanced and powered by a 34cc engine. With a 16-inch cutting bar, it strikes a perfect balance between power and portability, making it ideal for pruning and small to medium tree felling. The high visibility wrap handle provides extra comfort and control during operation.

The P3818AV further enhances user experience with its advanced anti-vibration technology, which significantly reduces the vibrations felt through the handles. This model features an 18-inch guide bar, making it versatile for various cutting tasks, from firewood to storm cleanup.

The P4018AV and P4018WT bring additional power to the table. The P4018AV has a similar engine and features to the BH model but in a different configuration, while the P4018WT is designed for tougher jobs with a fully-wrapped handle for improved grip and handling. The rugged construction of both models ensures they can withstand rigorous use in demanding environments.

Together, these Poulan chainsaws provide a range of features that cater to different needs—from light gardening projects to heavy-duty logging tasks. With a combination of power, ergonomic design, and innovative technology, Poulan chainsaws stand out as reliable tools for outdoor enthusiasts and professionals alike.