Poulan P4018WT, P4018 P4018WM, P4018AV BH, P3818AV P4018AV, P3314WSA P3416, P3516PR Storage

Page 16

6.Reinstall spark arresting screen, exhaust outlet cover, and nut. Tighten nut securely.

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY sec- tion.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place

and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage.

SStore in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel stabilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manual de Instrucciones Manuel d’Instructions 545137250 11/30/06Plan Ahead Starting ReminderTions found in this manual Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Assembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Throttle LOCK-OUT Chain Brake CHOKE/FAST Idle LeverPrimer Bulb Before Starting EngineImportant Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Right Foot Through Rear HandleBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeCutting a Fallen Tree Important PointsBucking Using a LOG or Support Stand Bucking Without a SupportLimbing and Pruning Important Points LimbingService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Engine Load Adjustment EngineOther Limited Warranty Ligations The U.S. EnvironmentalNANCE, Replacement and Repair
Related manuals
Manual 4 pages 35.01 Kb

P4018 P4018WM, P3516PR, P4018WT, P3314WS, P3818AV P4018AV specifications

The Poulan brand has established itself as a reliable name in outdoor power equipment, particularly with its diverse range of chainsaws designed for various cutting needs. The models P4018AV BH, P3314WSA, P3416, P3818AV, P4018AV, P3314WS, and P4018WT offer users cutting-edge technology and features tailored for efficiency, durability, and ease of use.

The P4018AV BH is a standout model featuring a powerful 40cc, 2-cycle engine that delivers robust cutting performance. Equipped with an anti-vibe handle system, it minimizes user fatigue during extended use. Its 18-inch cutting bar increases the cutting capacity, making it suitable for larger trees and branches. The tool-less chain tensioning system allows for quick adjustments, ensuring optimal performance without the need for additional tools.

The P3314WSA offers a 33cc engine, making it a lightweight option for casual users. This model is particularly suitable for homeowners and novice users who require a dependable chainsaw for light to moderate cutting tasks. The 14-inch guide bar provides excellent maneuverability, while the automatic oiler ensures continuous lubrication of the chain for smoother operation.

Moving to the P3416, this chainsaw is well-balanced and powered by a 34cc engine. With a 16-inch cutting bar, it strikes a perfect balance between power and portability, making it ideal for pruning and small to medium tree felling. The high visibility wrap handle provides extra comfort and control during operation.

The P3818AV further enhances user experience with its advanced anti-vibration technology, which significantly reduces the vibrations felt through the handles. This model features an 18-inch guide bar, making it versatile for various cutting tasks, from firewood to storm cleanup.

The P4018AV and P4018WT bring additional power to the table. The P4018AV has a similar engine and features to the BH model but in a different configuration, while the P4018WT is designed for tougher jobs with a fully-wrapped handle for improved grip and handling. The rugged construction of both models ensures they can withstand rigorous use in demanding environments.

Together, these Poulan chainsaws provide a range of features that cater to different needs—from light gardening projects to heavy-duty logging tasks. With a combination of power, ergonomic design, and innovative technology, Poulan chainsaws stand out as reliable tools for outdoor enthusiasts and professionals alike.
Top Page Image Contents