Poulan 545137250 Check Fuel Mixture Level, Lubrication, Inspect and Clean Unit and Decals

Page 15

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when ex- cess heating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHECK FUEL MIXTURE LEVEL

S See FUELING ENGINE under the OP- ERATION section.

LUBRICATION

Bar Oil

Fill Cap

SSee GUIDE BAR AND CHAIN OIL under the OPERATION section.

INSPECT AND CLEAN UNIT AND DECALS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild deter- gent.

SWipe off unit with a clean dry cloth.

CHECK CHAIN BRAKE

See CHAIN BRAKE in the OPERATION section.

CLEAN AIR FILTER

CAUTION: Do not clean filter in gasoline or other flammable solvent to avoid creating a fire hazard or producing harmful evaporative emissions.

Cleaning the air filter:

A dirty air filter decreases the life and perfor- mance of the engine and increases fuel con- sumption and harmful emissions. Always clean your air filter after 10 tanks of fuel or 5 hours of operation, whichever comes first. Clean more frequently in dusty conditions. A used air filter can never be completely cleaned. It is advisable to replace your air fil-

ter with a new one after every 50 hours of op- eration, or annually, whichever comes first.

1.Loosen 3 screws on cylinder cover.

2.Remove cylinder cover.

3.Remove air filter cover and air filter.

4.Clean the air filter using hot soapy water. Rinse with clean cool water. Air dry com- pletely before reinstalling.

5.Reinstall air filter and air filter cover.

6.Reinstall cylinder cover and 3 screws. Tighten securely.

Cylinder

Air FilterCover

Cover

Air Filter

INSPECT MUFFLER AND SPARK ARRESTING SCREEN

WARNING: The muffler on this product contains chemicals known to the State of California to cause cancer.

As the unit is used, carbon deposits build up on the muffler and spark arresting screen, and must be removed to avoid creating a fire hazard or affecting engine performance.

Replace the spark arresting screen if breaks occur.

Spark Exhaust

Arresting Outlet

Screen Cover

Nut

Muffler

CLEANING THE SPARK ARREST- ING SCREEN

Cleaning is required every 25 hours of op- eration or annually, whichever comes first.

1.Loosen and remove the nut from the ex- haust outlet cover.

2.Remove the exhaust oulet cover.

3.Remove spark arresting screen. Handle screen carefully to prevent damage.

4.Clean the spark arresting screen gently with a wire brush. Replace screen if breaks are found.

5.Replace any broken or cracked muffler parts.

15

Image 15
Contents 545137250 11/30/06 Manual de Instrucciones Manuel d’InstructionsStarting Reminder Plan AheadTions found in this manual Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Reduce the Chance of KickbackMaintain Control Avoid Pinch-KickbackKickback Safety Features Chain Brake and CKA AngleChain saws as set by Ansi B175.1 Attaching the BAR & Chain If not AssemblyAdjusting the tension Chain TensionChecking the tension ON/STOP Switch Throttle Trigger OperationKnow Your Chain SAW Before Starting Engine Throttle LOCK-OUT Chain BrakeCHOKE/FAST Idle Lever Primer BulbRight Foot Through Rear Handle Important Points to RememberStarting a Warm Engine Difficult Starting or starting a flooded engineTree Felling Techniques Braking function control Caution The chain brake must beInertia activating function control Operating TipsImportant Points Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen TreeLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsService Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Cleaning the Spark ARREST- ING ScreenStorage Load Adjustment Engine EngineOther Ligations The U.S. Environmental Limited WarrantyNANCE, Replacement and Repair