Poulan 545137250 Operation, Know Your Chain SAW, ON/STOP Switch Throttle Trigger

Page 8

3.Using bar tool, roll chain around guide bar to ensure all links are in bar groove.

4.Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn ad- justing screw 1/4 turn clockwise. Repeat until sag does not exist.

Adjusting Screw -- 1/4 Turn

5.While lifting tip of guide bar, tighten bar nuts securely with the bar tool.

Bar Nuts

6.Use the screwdriver end of the bar tool to move chain around guide bar.

7.If chain does not rotate, it is too tight. Slightly loosen bar nuts and loosen chain by turning the adjusting screw 1/4 turn counterclockwise. Retighten bar nuts.

8.If chain is too loose, it will sag below the guide bar. DO NOT operate the saw if the chain is loose.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

OPERATION

KNOW YOUR CHAIN SAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

Chain

 

Front Hand Guard

Front Handle

 

Adjustment Tool

 

 

 

 

Starter Rope

 

(Bar Tool)

 

 

 

 

 

 

 

 

 

 

 

 

 

ON/STOP

Choke/

 

 

 

 

Switch

 

Chain

Muffler

 

Fast Idle

 

 

Lever

Bar

Bar Oil Fill Cap

 

 

 

 

Sprocket

 

 

 

 

 

Hole

Starter Housing

Fuel Mix Fill Cap

Primer Bulb

 

 

Cylinder Cover

 

 

 

 

Throttle

 

Chain

 

Chain

Lockout

 

Brake

 

Direction

 

 

 

 

of Travel

Rear

 

 

 

 

 

Adjusting Screw

 

 

Handle

 

 

 

 

 

 

 

 

 

 

Chain

Guide Bar

Throttle

 

 

 

Clutch Cover

Catcher

 

 

Trigger

Bar Nuts

 

 

 

 

ON/STOP SWITCH

THROTTLE TRIGGER

 

The ON/STOP SWITCH is used to stop the

The THROTTLE TRIGGER controls engine

engine.

 

speed.

 

 

 

8

Image 8
Contents Manual de Instrucciones Manuel d’Instructions 545137250 11/30/06Tions found in this manual Starting ReminderPlan Ahead Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Assembly Attaching the BAR & Chain If notChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP Switch Throttle TriggerOperation Throttle LOCK-OUT Chain Brake CHOKE/FAST Idle LeverPrimer Bulb Before Starting EngineImportant Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Right Foot Through Rear HandleBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeCutting a Fallen Tree Important PointsBucking Using a LOG or Support Stand Bucking Without a SupportLimbing and Pruning Important Points LimbingService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Other Load Adjustment EngineEngine Limited Warranty Ligations The U.S. EnvironmentalNANCE, Replacement and Repair