Poulan 545047502 Tree Felling Techniques, Felling Large Trees, Notch CUT and Felling the Tree

Page 11

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or en- gine can result.

S Release the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load, unneces- sary wear can occur to the chain, bar, and engine.

S To avoid losing control when cut is com- plete, do not put pressure on saw at end

of cut.

S Stop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near build- ings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree makes contact with any utility line, the utility company should be notified immediately.

SCarefully plan your sawing operation in ad- vance.

SClear the work area. You need a clear area

all around the tree so you can have secure footing.

SStudy the natural conditions that can cause the tree to fall in a particular direction.

Natural conditions that can cause a tree to fall in a particular direction include:

SThe wind direction and speed.

S The lean of the tree. The lean of a tree might not be apparent due to uneven or sloping terrain. Use a plumb or level to de- termine the direction of tree lean.

SWeight and branches on one side. S Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted, it can snap and fall toward the operator. Check for broken or dead branches which can fall on you while cutting.

Make sure there is enough room for the tree to fall. Maintain a distance of 2-1/2tree lengths from the nearest person or other objects. En- gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, sta- ples, and wire from the tree where cuts are to be made.

Plan a clear retreat path to the rear and diag- onal to the line of fall.

Plan a clear retreat path

Direction of Fall

45_

FELLING LARGE TREES

(6 inches in diameter or larger)

The notch method is used to fell large trees. A notch is cut on the side of the tree in the de- sired direction of fall. After a felling cut is made on the opposite side of tree, the tree will tend to fall into the notch.

NOTE: If the tree has large buttress roots, remove them before making the notch. If us- ing saw to remove buttress roots, keep saw chain from contacting ground to prevent dull- ing of the chain.

NOTCH CUT AND FELLING THE TREE

SMake notch cut by cutting the top of the notch first. Cut through 1/3 of the diameter of the tree. Next complete the notch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut, remove the notch of wood from the tree.

Final (felling) cut here, 2 inches (5 cm) above center of notch

First cut

Notch

Hinge

Second cut

S After removing the wood from the notch, make the felling cut on the opposite side of the notch. This is done by making a cut about two inches higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form a hinge. This hinge will help prevent the tree from falling in the wrong direction.

Hinge holds tree on stump and helps control fall

Opening of felling cut

Closing of notch

11

Image 11
Contents PP4620AVHD Plan Ahead Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionYour left arm straight with the elbow locked Maintain ControlReduce the Chance of Kickback Do not cut more than one log at a timeChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Attaching the BAR & Chain If not AssemblyComputed kickback angle CKA Table Attaching the Bumper SpikeCutters Adjusting the tensionInside view Chain Brake Adjustment located on Chain Brake Tip BarOperation BAR and Chain Lubrication Fueling & LubricationStarting Fueling EngineImportant Points Cutting MethodsStarting a Warm Engine Chain BrakeNotch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Bucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingErly Limbing and Pruning Important PointsLimbing PruningAIR Filter ServiceCleaning the air filter Cleaning the Spark Arresting ScreenStorage Trouble Cause Remedy Troubleshooting TableNeed Service PART? Need ASSISTANCE?Electrolux Home PRODUCTS, INC Limited WarrantyLigations The U. S. Environmental NANCE, Replacement and Repair of Emission Related Parts Any

545047502 specifications

The Poulan 545047502 is a versatile gas-powered chainsaw designed for both professional and home use. Renowned for its reliability, performance, and user-friendly features, this chainsaw caters to a wide range of cutting tasks, from occasional trimming to more demanding jobs in the backyard or on a job site.

At the heart of the Poulan 545047502 is its robust 50cc engine, which delivers substantial power to tackle tough cutting jobs with ease. This engine's advanced design ensures efficient fuel consumption while maintaining strong performance. The chainsaw is equipped with a 20-inch bar and chain, offering ample length for cutting larger logs and branches, making it an excellent choice for tree felling, limb removal, and firewood cutting.

One of the standout features of the Poulan 545047502 is its ProLite chain, which is designed for faster cutting and superior performance. This technology enables smoother cuts and minimizes kickback, enhancing user safety. The chainsaw also boasts an easy-start system, enabling users to fire up the engine with minimal effort, thereby reducing frustration and waiting time before beginning work.

The chainsaw integrates an automatic oiler, which provides consistent lubrication to the bar and chain during operation. This feature not only prolongs the life of the chain but also ensures optimal cutting efficiency, reducing the risk of chain binding and damage. The tool-less access air filter makes maintenance straightforward, enabling users to keep the chainsaw running at peak performance.

Ergonomics play a crucial role in the design of the Poulan 545047502. It features a comfortable grip and balanced handling, allowing users to operate it for extended periods without undue fatigue. The anti-vibration system minimizes operator fatigue, making the chainsaw more comfortable to use during prolonged tasks.

Additionally, the Poulan 545047502 is designed with safety as a priority. It includes a chain brake that activates in the event of kickback, protecting the user from potential injury. The saw also has a safety throttle lock to prevent accidental starts, enhancing overall user confidence during operation.

In summary, the Poulan 545047502 is a powerful, efficient, and user-friendly chainsaw. With its impressive engine performance, advanced technologies, and ergonomic design, it stands out as a reliable tool for anyone looking to tackle cutting tasks with ease and safety. Whether you're a seasoned professional or a DIY enthusiast, this chainsaw has the features you need to get the job done effectively.