Poulan 545047503 instruction manual Limbing and Pruning Important Points, ING Without a Support

Page 13

Using a log for support 2nd Cut

1st Cut

1st Cut

2nd Cut

Using a support stand 2nd Cut

1st Cut

1st Cut

2nd Cut

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or objects at the nose of the guide bar when limbing or pruning. Allowing such contact can result in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, plat- forms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

S Work slowly, keeping both hands firmly gripped on the saw. Maintain secure footing and balance.

SWatch out for springpoles. Springpoles are small size limbs which can catch the saw

chain and whip toward you or pull you off bal- ance. Use extreme caution when cutting small size limbs or slender material.

S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

S Keep a clear work area. Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SAlways limb a tree after it is cut down. Only then can limbing be done safely and prop- erly.

SLeave the larger limbs underneath the felled

tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and limbs.

Remove small limbs with one cut.

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

S Remove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and free- ly hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your first cut 1/3 of the way through the bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch (2.5 to 5 cm) collar from the truck of the tree.

Second cut

Third cut

Collar

First cut

Pruning technique

13

Image 13
Contents 12/8/05 Electrolux Home Products, IncPlan Ahead Hearing Safety Hat Protection Eye Snug FittingMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control WE do not REP Chain Brake and CKA AngleResent and YOU should not AS Sume That the Chain Brake willChain adjustment tool Bar Tool AssemblyAttaching the BAR & Chain If not ShippingAdjusting Screw Adjusting the tensionChain Tension Checking the tensionOperation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Cation Always stop the engine before removing the oil capStarting a Warm Engine Choke Lever Move ON/STOP switch to the on posi- tionDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beTree Felling Techniques Operating TipsFelling Large Trees Notch CUT and Felling the TreeCutting a Fallen Tree Bucking Using a LOG or Support StandImportant Points Types of Cutting Used for BuckingLimbing Limbing and Pruning Important PointsPruning ING Without a SupportService Clean AIR Filter Inspect and Clean Unit and DecalsCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Engine Load Adjustment EngineOther Electrolux Home PRODUCTS, INC Tions The U.S. Environmental ProtectionConsequential Damages Electro