Poulan 545186802 instruction manual Troubleshooting Table Cause Remedy, Load Adjustment Engine

Page 18

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit.

 

TROUBLE

CAUSE

REMEDY

 

 

 

 

 

Engine will not

1. Ignition switch off.

1. Move ignition switch to ON.

 

start or will run

2. Engine flooded.

2. See “Difficult Starting” in

 

only a few

 

 

 

Operation Section.

 

seconds after

3. Fuel tank empty.

3. Fill tank with correct fuel mixture.

 

starting.

4. Spark plug not firing.

4. Install new spark plug.

 

 

5. Fuel not reaching

5. Check for dirty fuel filter; replace.

 

 

 

carburetor.

 

Check for kinked or split fuel line;

 

 

 

 

 

repair or replace.

 

 

 

 

 

 

Engine will

1.

Carburetor requires

1. See “Carburetor Adjustment” in the

 

not idle

 

adjustment.

 

Service and Adjustments Section.

 

properly.

2.

Crankshaft seals worn.

2. Contact an authorized service dealer.

 

 

 

 

 

 

 

Engine will not

1.

Air filter dirty.

1.

Clean or replace air filter.

 

accelerate,

2.

Spark plug fouled.

2.

Clean or replace plug and regap.

 

lacks power,

3.

Chain brake engaged.

3.

Disengage chain brake.

 

or dies under

4.

Carburetor requires

4.

Contact an authorized service dealer.

 

a load.

 

adjustment.

 

 

 

 

 

 

 

Engine

1. Too much oil mixed with

1. Empty fuel tank and refill with

 

smokes

 

gasoline.

 

correct fuel mixture.

 

excessively.

 

 

 

 

 

Chain moves

1. Idle speed requires

1. See “Carburetor Adjustment” in the

 

at idle speed.

 

adjustment.

 

Service and Adjustments Section.

 

 

2. Clutch requires repair.

2.

Contact an authorized service dealer.

 

 

 

 

 

 

18

Image 18
Contents Manual de Instrucciones Manuel d’Instructions Starting Reminder Plan AheadTions found in this manual Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Maintain ControlReduce the Chance of Kickback Avoid Pull-InKickback Safety Features Chain Brake and CKA AngleAttaching the Bumper Spike If not already attached AssemblyComputed kickback angle CKA Table Attaching the BAR & Chain If notChecking the tension Adjusting the tensionAdjusting Screw Tensioning Rack Tip BarKnow Your SAW ON/STOP SwitchOperation Throttle TriggerCHOKE/FAST Idle Lever Chain BrakeChain Tension Difficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine To stop the engine move the ON/STOPInertia activating function control Cutting MethodsBraking function control Important PointsCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Types of Cutting Used for BuckingLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingPruning ServiceCleaning the Spark Arresting Screen AIR FilterIdle Speed-T Carburetor AdjustmentsBAR Maintenance Back View of MufflerTo Sharpen Chain Chain SharpeningTools required Ignition TimingStorage Troubleshooting Table Cause Remedy Load Adjustment EngineEmpty fuel tank and refill with Poulan PRO Limited WarrantyStevens Creek Road Augusta, GA Ligations The U.S. EnvironmentalNANCE, Replacement and Repair of Emission Related Parts Any