Poulan 178085 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

1/2" wrenches

Utility knife

(2)

9/16" wrench

Tire pressure gauge

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 5/16 hex bolt and locknut. Tighten securely.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

3/8 HEX BOLT

 

3/8 LOCK WASHER

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

STEERING

 

BOOT

 

TABS

ADAPTER

 

 

EXTENSION

 

SHAFT

 

5/16 HEX

5/16

BOLT

LOCKNUT

 

 

TAB

LOWER

SLOTS

 

STEERING

 

SHAFT

 

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position and open battery box door.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PR1742STC Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesContents of Hardware Pack To Remove Tractor from Carton Tools Required for AssemblyHOW to SET UP Your Tractor Before Removing Tractor from SkidInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessEngine on Engine OFF OIL Pressure Lights on Battery Reverse Forward FastSee Safety Rules Section LightKnow Your Tractor HOW to USE Your Tractor Towing Carts and Other Attachments Before Starting the EngineTo Transport ADD GasolineMowing Tips To Start Engine See FigMulching Mowing Tips Lubrication Chart General RecommendationsBefore Each USE Tractor Belts Clean AIR ScreenEngine Transaxle CoolingSpark Plugs CleaningMuffler Engine OIL FilterTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust CarburetorEngine OIL OtherFuel System CylindersTroubleshooting Points OFF Schematic Tractor - Model Number PR1742STCElectrical 2122KEY Part NO. NO.DESCRIPTION Chassis and Enclosures 174619 176554Drive 72140608 175410175765 73900600Steering Assembly 175146 175121177876 175118Seat Assembly 174894178085 DecalsWheels and Tires 178086Engine 170551 Control Th/ch Flag Mower Deck 174493 Tractor Model Number PR1742STC Mower Lift159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Sighting GuideParts and Service

178085 specifications

The Poulan 178085 is a highly regarded chainsaw known for its durability, efficiency, and ease of use. Designed primarily for homeowners and light-duty commercial use, this model stands out for its impressive balance between power and user-friendliness. Whether tackling tree trimming, firewood cutting, or general yard maintenance, the Poulan 178085 delivers reliable performance.

One of the key features of the Poulan 178085 is its robust engine. Equipped with a 40cc gas-powered engine, this chainsaw generates enough power to handle various cutting tasks with ease. The engine is designed to be fuel-efficient, allowing users to maximize runtime while minimizing fuel consumption and emissions. Additionally, its easy-start technology ensures that the chainsaw can be fired up with minimal effort, making it accessible even for those who may be new to using chainsaws.

The chainsaw boasts a 16-inch bar, which provides an optimal cutting length for most home and garden applications. This ideal size strikes a balance between maneuverability and cutting capability, allowing users to cut through branches and logs efficiently. The low-kickback design of the bar and chain improves safety during operation, making it less likely for the saw to kick back unexpectedly.

Another notable characteristic of the Poulan 178085 is its lightweight construction. Weighing in at only about 10 pounds, this chainsaw is easy to handle and reduces user fatigue during extended periods of use. Its comfortable grip and well-placed controls enhance the overall user experience, allowing for smoother operation and better precision while cutting.

To further enhance safety, the Poulan 178085 includes a chain brake feature that stops the chain in the event of kickback. This critical safety mechanism is a vital addition for both novice and experienced users, providing peace of mind while operating the saw.

In terms of maintenance, the Poulan 178085 features an automatic oiling system that keeps the chain lubricated during cutting, ensuring a longer lifespan for both the chain and bar. This feature reduces the need for manual lubrication, making it more convenient for users.

In summary, the Poulan 178085 is a versatile and reliable chainsaw equipped with a powerful engine, a well-designed bar, and a range of safety features. Its lightweight design and user-friendly technologies make it an excellent choice for anyone looking to manage their yard work effectively and safely. Whether you are a seasoned professional or a DIY enthusiast, the Poulan 178085 is a tool that meets the demands of modern cutting and trimming tasks.
Top Page Image Contents