Poulan 177545 owner manual Tractor

Page 15

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 11)

•Raise mower to highest position to allow access to blades.

•Remove hex bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble hex bolt, lock washer and flat washer in exact order as shown.

•Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

 

MANDREL

EDGE UP

BLADE

ASSEMBLY

 

 

CENTER

HOLE

FLAT WASHER

LOCK WASHER

STAR

 

HEX BOLT (GRADE

8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 11

TO SHARPEN BLADE (See Fig. 12)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

 

OR PIN

 

FIG. 12

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not

15necessary.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents PRK17G42STA Safe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Customer Responsibilities Product SpecificationsContents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureLight Battery Reverse Forward FastSee Safety Rules Section Engine on Engine OFF OIL Pressure Lights onKnow Your Tractor HOW to USE Your Tractor ADD Gasoline Before Starting the EngineTo Transport Towing Carts and Other AttachmentsMowing Tips To Start Engine See FigMulching Mowing Tips Lubrication Chart General RecommendationsBefore Each USE Tractor Engine Engine OIL Filter CleaningMuffler Spark PlugsTo Remove Mower See Fig To Install Mower See FigFRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigInterlocks and Relays Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbTo Adjust Carburetor To Adjust Throttle Control Cable See FigCylinders OtherFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PRK17G42STA SchematicElectrical KEY Part NO. NO.DESCRIPTION 142 KEY Part Description Chassis and EnclosuresDrive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Wheels and Tires DecalsEngine 170805 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

177545 specifications

The Poulan 177545 is a powerful and versatile chainsaw designed for both professional and residential use, catering to a wide range of cutting needs. This model stands out due to its robust construction and innovative features, making it an ideal choice for anyone seeking efficient and reliable performance.

One of the key features of the Poulan 177545 is its powerful engine. Equipped with a high-performance 46cc two-cycle engine, this chainsaw provides ample power for tackling tough cutting jobs, whether they involve felling trees, pruning branches, or cutting firewood. The engine is designed for easy starting, thanks to the built-in primer bulb and advanced start system, minimizing downtime and allowing users to get to work quickly.

The 18-inch bar length of the Poulan 177545 is another significant characteristic, providing users with a perfect balance between reach and control. This makes it suitable for both larger and smaller cutting tasks, offering versatility for different applications. The chainsaw also features a low-kickback chain design, which enhances safety and minimizes the risk of injury during operation.

Another notable technology incorporated into the Poulan 177545 is its automatic oiling system. This feature ensures that the chain remains properly lubricated during use, reducing friction and wear, which prolongs the lifespan of the chain and bar. Additionally, the chainsaw's tool-free chain tensioning system makes adjustments quick and easy, allowing users to maintain peak performance with minimal effort.

The design of the Poulan 177545 puts user comfort and safety at the forefront. It features a comfortable grip handle that reduces vibrations, making extended use more manageable. The safety chain brake adds another layer of protection, allowing for quick and responsive action in case of kickback.

Lastly, the Poulan 177545 is engineered with an emphasis on durability and ease of maintenance. The durable construction ensures that the chainsaw can withstand regular use in various environments. With its user-friendly design and maintenance features, the Poulan 177545 is a reliable tool for both seasoned professionals and DIY enthusiasts alike. In summary, the Poulan 177545 offers a combination of power, safety, and ease of use, making it an exceptional choice for anyone in need of a dependable chainsaw.
Top Page Image Contents