Poulan 177545 Transaxle Gear Shift Lever Neutral Adjustment See Fig, Front Wheel TOE-IN/CAMBER

Page 21

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 25)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

LOCK GATE

ADJUSTMENT

BOLT

FIG. 25

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 26)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 26

TO START ENGINE WITH A WEAK BATTERY (See Fig. 27)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the CUSTOMER RESPON- SIBILITIES section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PRK17G42STA Safe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Customer Responsibilities Product SpecificationsContents of Hardware Pack HOW to SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessSee Safety Rules Section Battery Reverse Forward FastEngine on Engine OFF OIL Pressure Lights on LightKnow Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTowing Carts and Other Attachments ADD GasolineMowing Tips To Start Engine See FigMulching Mowing Tips Lubrication Chart General RecommendationsBefore Each USE Tractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Remove Mower See Fig To Install Mower See FigFRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Gear Shift Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigFuel System OtherEngine OIL CylindersTroubleshooting Points OFF Tractor - Model Number PRK17G42STA SchematicElectrical KEY Part NO. NO.DESCRIPTION 142 KEY Part Description Chassis and EnclosuresDrive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Wheels and Tires DecalsEngine 170805 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

177545 specifications

The Poulan 177545 is a powerful and versatile chainsaw designed for both professional and residential use, catering to a wide range of cutting needs. This model stands out due to its robust construction and innovative features, making it an ideal choice for anyone seeking efficient and reliable performance.

One of the key features of the Poulan 177545 is its powerful engine. Equipped with a high-performance 46cc two-cycle engine, this chainsaw provides ample power for tackling tough cutting jobs, whether they involve felling trees, pruning branches, or cutting firewood. The engine is designed for easy starting, thanks to the built-in primer bulb and advanced start system, minimizing downtime and allowing users to get to work quickly.

The 18-inch bar length of the Poulan 177545 is another significant characteristic, providing users with a perfect balance between reach and control. This makes it suitable for both larger and smaller cutting tasks, offering versatility for different applications. The chainsaw also features a low-kickback chain design, which enhances safety and minimizes the risk of injury during operation.

Another notable technology incorporated into the Poulan 177545 is its automatic oiling system. This feature ensures that the chain remains properly lubricated during use, reducing friction and wear, which prolongs the lifespan of the chain and bar. Additionally, the chainsaw's tool-free chain tensioning system makes adjustments quick and easy, allowing users to maintain peak performance with minimal effort.

The design of the Poulan 177545 puts user comfort and safety at the forefront. It features a comfortable grip handle that reduces vibrations, making extended use more manageable. The safety chain brake adds another layer of protection, allowing for quick and responsive action in case of kickback.

Lastly, the Poulan 177545 is engineered with an emphasis on durability and ease of maintenance. The durable construction ensures that the chainsaw can withstand regular use in various environments. With its user-friendly design and maintenance features, the Poulan 177545 is a reliable tool for both seasoned professionals and DIY enthusiasts alike. In summary, the Poulan 177545 offers a combination of power, safety, and ease of use, making it an exceptional choice for anyone in need of a dependable chainsaw.
Top Page Image Contents