Poulan 530165555 Cutting a Fallen Tree, Important Points, Types of Cutting Used for Bucking

Page 12

Hinge holds tree on stump and helps control fall

Opening of felling cut

Closing of notch

NOTE: Before felling cut is complete, use wedges to open the cut if necessary to control the direction of fall. To avoid kickback and chain damage, use wood or plastic wedges, but never steel or iron wedges.

SBe alert to signs that the tree is ready to fall: cracking sounds, widening of the fell- ing cut, or movement in the upper branches.

SAs tree starts to fall, stop saw, put it down, and get away quickly on your planned re-

treat path.

SDO NOT cut down a partially fallen tree with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log size.

WARNING: Do not stand on the log being cut. Any portion can roll causing loss of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

SCut only one log at a time.

S Cut shattered wood very carefully; sharp pieces of wood could be flung toward opera- tor.

SUse a sawhorse to cut small logs. Never allow another person to hold the log while cutting and never hold the log with your leg

or foot.

SDo not cut in an area where logs, limbs, and roots are tangled such as in a blown down area. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Re- start the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting

Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

First cut on compression side of log

Second cut

Second cut

First cut on compression side of log

BUCKING WITHOUT A SUPPORT

SOvercut through 1/3 of the diameter of the log.

SRoll the log over and finish with a second

overcut.

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustrations for cutting logs with a compres- sion side.

BUCKING USING A LOG OR

SUPPORT STAND

SRemember your first cut is always on the

compression side of the log.

(Refer to the illustrations below for your first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

12

Image 12
Contents PP3816 AV / PP4218 AV For Occasional Use Only 12/8/05Identification of Symbols Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance of KickbackMaintain Control Chain Brake and CKA Angle WE do not REPResent and YOU should not AS Sume That the Chain Brake willAssembly Adjusting Screw Tensioning RackAttaching the BAR & Chain If not CuttersAdjusting the tension Chain TensionChecking the tension Operation Before Starting Engine Fueling Engine BAR and Chain LubricationImportant Points to Remember Cation Always stop the engine before removing the oil capStarting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points LimbingPruning ING Without a SupportService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Empty fuel tank and refill withTions The U.S. Environmental Protection Electrolux Home PRODUCTS, INCConsequential Damages Electro

530165555 specifications

The Poulan 530165555 is a high-performance chainsaw engineered to tackle a wide range of cutting tasks, from trimming branches to felling large trees. Known for its reliability and ease of use, this model has gained popularity among both DIY enthusiasts and professionals alike.

One of the standout features of the Poulan 530165555 is its powerful engine. It is equipped with a robust two-cycle engine that delivers excellent power output, allowing users to efficiently cut through thick wood with ease. The engine is designed to provide maximum torque, which means that users can expect consistent performance even under demanding conditions.

Durability is another key characteristic of the Poulan 530165555. The chainsaw is constructed with high-quality materials that can withstand the rigors of regular use. Its heavy-duty frame and components ensure longevity and reliability, making it a worthy investment for anyone looking to maintain their property or work in forestry.

The Poulan 530165555 also boasts user-friendly features that enhance the overall experience. The chainsaw is designed with an ergonomic handle that provides a comfortable grip, reducing fatigue during prolonged operation. Additionally, the lightweight design allows for easy maneuverability, making it an ideal choice for overhead cuts and precise trimming.

Safety is a top priority, and the Poulan 530165555 incorporates several safety features to protect users. It includes a chain brake that engages automatically in the event of kickback, ensuring that the operator remains safe while working. Furthermore, the chainsaw features a low kickback bar and chain, contributing to a more predictable cutting action.

Another notable technology is the easy-start mechanism that simplifies ignition, allowing users to start the chainsaw with minimal effort. This feature is especially beneficial for those who may not have extensive chainsaw experience.

Maintenance is an essential aspect of any tool, and the Poulan 530165555 shines in this area as well. The chainsaw comes with a tool-less chain tensioning system, enabling users to adjust the chain quickly and easily without the need for additional tools. This ensures optimal performance and extends the life of the chain.

In conclusion, the Poulan 530165555 is a well-rounded chainsaw that combines power, durability, user-friendly features, and safety technologies. Its ability to handle various cutting tasks makes it an indispensable tool for homeowners and professionals alike. Whether you are pruning trees, cutting firewood, or tackling larger cutting jobs, the Poulan 530165555 stands out as a reliable and efficient solution.