Poulan 530165555-01 instruction manual Storage

Page 16

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY section.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage. S Store in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

S Oil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message

labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/Weed Eater 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel sta- bilizer to your fuel tank.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distrib-

ute oil.

SReplace spark plug with new one of rec- ommended type and heat range.

16

Image 16
Contents PP3816 AV / PP4218 AV For Occasional Use Only 530165555-01 8/20/04Identification of Symbols Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Chain Brake and CKA Angle WE do not REPResent and YOU should not AS Sume That the Chain Brake willAssembly Adjusting Screw Tensioning RackAttaching the BAR & Chain If not CuttersChain Tension Adjusting the tensionChecking the tension Operation Before Starting Engine Fueling Engine BAR and Chain LubricationImportant Points to Remember Cation Always stop the engine before removing the oil capStarting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlTension in the Assembly section Operating TipsTree Felling Techniques Felling Large TreesBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points LimbingPruning ING Without a SupportService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine OtherLigations The U. S. Environmental Electrolux Home PRODUCTS, INCNANCE, Replacement and Repair of Emission Related Parts Any

530165555-01 specifications

The Poulan 530165555-01 is a robust and versatile chainsaw designed for both professional landscapers and home users seeking reliable performance for various cutting tasks. Renowned for its durability and efficiency, this model combines modern technology with user-friendly features to ensure a seamless cutting experience.

One of the standout characteristics of the Poulan 530165555-01 is its powerful engine. Equipped with a potent 50cc two-stroke engine, it offers a balance of power and lightweight design, making it suitable for prolonged use without causing excessive fatigue. The engine is designed for optimal fuel efficiency, enabling users to accomplish more tasks with less refueling. This is particularly beneficial for those who need to tackle larger jobs or for professional users who rely on their equipment for daily workloads.

The chainsaw features an adjustable automatic oiling system, which ensures that the bar and chain are consistently lubricated. This system helps to enhance the lifespan of the cutting components while also minimizing friction and heat during operation. The 20-inch bar length is ideal for a variety of cutting tasks, from felling trees to trimming branches, offering versatility for different projects.

Safety is a top priority with the Poulan 530165555-01, and it includes several safety features designed to protect the user. The chain brake provides an immediate stop in the event of kickback, while the anti-vibration system reduces operator fatigue, allowing for longer periods of safe operation. Furthermore, the easy-start technology makes it simple for users of all experience levels to start the chainsaw with minimal effort, reducing the frustration often associated with traditional pull-start mechanisms.

Another notable feature is the tool-less chain tensioning system, which allows users to make quick adjustments to the chain tension without the need for additional tools. This innovation enhances convenience and empowers users to maintain optimal cutting performance on the fly.

In summary, the Poulan 530165555-01 is a well-rounded chainsaw that blends power, safety, and ease of use. Whether you're a seasoned professional or a homeowner tackling seasonal yard work, the combination of its durable construction, efficient operation, and user-friendly features makes it a reliable choice for various cutting needs. With this chainsaw in hand, users can confidently take on any task, knowing they have a dependable tool at their disposal.