Poulan 530163676 Limbing and Pruning Important Points, ING Without a Support

Page 13

1st Cut

2nd Cut

Using a support stand

2nd Cut

1st Cut

1st Cut

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

S Remove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and free- ly hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your first cut 1/3 of the way through the bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch collar from the truck of the tree.

2nd Cut

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or objects at the nose of the guide bar when limbing or pruning. Allowing such contact can result in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, plat- forms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

S Work slowly, keeping both hands firmly gripped on the saw. Maintain secure footing and balance.

SWatch out for springpoles. Springpoles are small size limbs which can catch the saw chain and whip toward you or pull you off bal- ance. Use extreme caution when cutting small size limbs or slender material.

S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

S Keep a clear work area. Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SAlways limb a tree after it is cut down. Only

then can limbing be done safely and prop- erly.

SLeave the larger limbs underneath the felled tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and limbs. Remove small limbs with one cut.

Second cut

Third cut

Collar

First cut

Pruning technique

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

We recommend all service and adjustments not listed in this manual be performed by an authorized or Master Service Dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level . . . . Before each use Bar lubrication . . . . . . . Before each use Chain tension . . . . . . . Before each use Chain sharpness . . . . Before each use For damaged parts . . Before each use For loose caps . . . . . . Before each use For loose fasteners. . . Before each use For loose parts . . . . . . Before each use

Inspect and Clean:

Bar . . . . . . . . . . . . . . . . Before each use Complete saw . . . . . . . After each use Air filter . . . . . . . . . . . . . Every 5 hours* Chain brake . . . . . . . . Every 5 hours* Spark arresting screen

and muffler . . . . . . . . . Every 25 hours* Replace spark plug . Yearly Replace fuel filter . . . Yearly

* Hours of Operation

13

Image 13
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance Kickback Kickback Safety FeaturesMaintain Control Avoid Obstructions Clear The Working AreaResent and YOU should not AS Chain Brake and CKA AngleSume That the Chain Brake will Protect YOU in the Event of a KickAlready attached Tip Bar Cutters Depth Gauge Chain TensionBar. If the chain does not rotate, it is too Front Hand GuardKnow Your Chain SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTBAR and Chain Lubrication Fueling EngineImportant Points to Remember Important Points Starting a Warm EngineFelling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Cutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points PruningLimbing ING Without a SupportCarburetor Adjustment Cleaning the Spark ARREST- ING ScreenAIR Filter Inspect Muffler and Spark Arresting ScreenNeed Service PART? BAR MaintenanceChain Sharpening Ignition TimingTroubleshooting Table Cause Remedy Tions The U.S. Environmental Protection Your Warranty Rights and Obliga