STurn idle speed screw (T) clockwise to in- crease engine speed.
STurn idle speed screw (T) counterclock- wise to decrease engine speed.
If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call
BAR MAINTENANCE
If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.
After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.
To maintain guide bar:
SMove ON/STOP switch to the STOP posi-
tion.
SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from saw.
S Clean the oil holes and bar groove after each 5 hours of operation.
Remove Sawdust From
Guide Bar Groove
Oil Holes
S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.
SWhen rail top is uneven, use a flat file to re- store square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove | Correct Groove |
Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-
ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.
CHAIN SHARPENING
Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.
IGNITION TIMING
Ignition timing is fixed and nonadjustable.
SPARK PLUG
The spark plug should be replaced each year to ensure the engine starts easier and runs better.
1.Loosen 3 screws on cylinder cover.
2.Remove the cylinder cover.
3.Pull off the spark plug boot.
4.Remove spark plug from cylinder and discard.
5.Replace with Champion
6.Reinstall the spark plug boot.
7.Reinstall the cylinder cover and 3 screws. Tighten securely.
Screws |
|
|
| Cylinder | |||||||
Spark |
|
|
|
|
|
|
|
|
| Cover | |
|
|
|
|
|
|
|
|
|
|
| |
Plug Boot |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| |||
Spark |
|
|
|
|
| ||||||
Plug |
|
|
|
|
| ||||||
STORAGE |
|
|
|
|
| ||||||
WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children.
SBefore storing, drain all fuel from the unit. Start engine and allow to run until it stops.
SClean the unit before storing. Pay particu- lar attention to the air intake area, keeping
it free of debris. Use a mild detergent and sponge to clean the plastic surfaces.
SDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an open flame from hot water heaters, electric
motors or switches, furnaces, etc.
SStore in a dry area out of the reach of chil- dren.
CAUTION: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.
NEED ASSISTANCE?
Call
NEED SERVICE PART?
Contact your dealer or place of purchase.
15