Poulan 161608 owner manual Mowing Tips, Purge Transmission

Page 14

OPERATION

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

Place tractor safely on level surface with engine off and parking brake set.

Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

Your tractor is now purged and now ready for normal operation.

MOWING TIPS

Tire chains cannot be used when the mower housing is attached to tractor.

Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distri- bution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 10).

If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

FIG. 10

14

Image 14
Contents Model NO. HD145H42G Mow only in daylight or good artificial light Turn off blades when not mowingSafe Operation Practices for Ride-On Mowers Do not use grass catcher on steep slopesModel NUMBERHD145H42G Serial Product SpecificationsCustomer Responsibilities Number Date of PurchaseMower Adjustment AdjustmentsBattery MowerContents of Hardware Pack Before Rolling Tractor OFF Skid Tools Required for AssemblyTo Remove Tractor from CAR- TON Unpack CartonInstall Seat See Fig HOW to SET UP Your TractorConnect Battery See Figs Adjust seat before tightening adjustment boltCheck Tire Pressure Assemble Gauge Wheels to Mower Deck See FigCheck Brake System Check Deck LevelnessLock Locked Reverse Neutral High LOW Battery Reverse Forward FastUnlocked Hydro Models onlyKnow Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills ADD Gasoline Before Starting the EngineCheck Engine OIL Level See Fig To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations Lubrication ChartService Dates Before Each USEBrake Operation BatteryTractor TiresTransaxle Cooling EngineBelts Transaxle Pump FluidAIR Filter See a Clean AIR Screen See aService air cleaner more often under dusty conditions Engine OIL Filter See BSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig To Remove Mower See FigRaise mower to its highest position To Level Mower HousingSIDE-TO-SIDE Adjustment See Figs To Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER Block up axle securelyTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysPreliminary Setting To Adjust Throttle Control Cable See FigTo Adjust Carburetor See Fig Final SettingTroubleshooting Points OFF Schematic Because of THIS,Tractor - Model Number HD145H42G ElectricalKEY Part Description Harness Eng B&S 14 OHV DualChassis and Enclosures 74780616 159530 Chassis Wldmt 140356 Drawbar Stretch 1749061274180512 19131312Drive 140607 Steering Assembly 10040600 14004419272016 124035X Support Shaft 126684XSeat Assembly LSB42 Wheels and TiresLBD48 LAO18Engine Muffler Exhaust LT B&S 14HP IC OHV Lift 139868 Arm Suspension Rear 3146R Retainer Spring 140302 Wire Asm Inner W/Plunger159460 73540600 Nut Crownlock 3/8-24Mower Deck Washer 17/32 x 15/16 x 12 Gauge 137729 Screw Hex Thd CutWasher Hard Blade Mower Vented Transaxle Hydro Gear Model Number 20 x 142986 Housing, Lower 15077875 x 1.25 x 142937 Swashplate, Variable 142965 PinService Notes Service Notes Box Service DepartmentCanada contact Orangeburg, SC 29116 USAThis OUT Dotted Lines Slope Only Ride UP and Down HillCUT

161608 specifications

The Poulan 161608 chainsaw is a robust tool designed for homeowners and professionals alike, offering a blend of power, efficiency, and user-friendly features. This chainsaw is part of Poulan’s line of reliable outdoor power equipment, making it an excellent choice for tackling various cutting tasks, from trimming branches to felling small trees.

One of the main features of the Poulan 161608 is its powerful engine. It is equipped with a 38cc 2-stroke gas engine, which provides ample power for demanding cutting applications. The engine is designed for durability and reliability, ensuring that users can rely on the chainsaw for a range of tasks without frequent breakdowns. Additionally, the engine is engineered for easy starting, thanks to the incorporation of a primer bulb and an adjustable choke system. This allows users to start the chainsaw effortlessly, even in colder weather conditions.

The Poulan 161608 also boasts a 16-inch bar and chain, providing a balance between maneuverability and cutting capacity. The length of the blade makes it suitable for a variety of jobs, whether you are pruning trees, cutting firewood, or performing light logging tasks. The chain is designed for quick and efficient cutting, ensuring that users can accomplish their tasks with minimal effort.

Safety is a priority for Poulan, and this chainsaw features a chain brake that helps protect the user by stopping the chain in case of kickback. The front handguard and rear handle are ergonomically designed for a secure grip, reducing fatigue during extended use. Furthermore, the anti-vibration technology integrated into the design helps absorb shock, providing increased comfort and control when operating the chainsaw.

Maintenance is made easy with the Poulan 161608, as it features an automatic oiling system that ensures the chain remains lubricated, reducing wear and tear and extending the life of the chainsaw. Additionally, the tool-less chain tensioning system allows users to easily adjust the chain without the need for additional tools, making it more convenient for on-the-go maintenance.

In summary, the Poulan 161608 is a powerful and efficient chainsaw that combines user-friendly features, safety mechanisms, and ease of maintenance. With its robust engine, reliable cutting performance, and ergonomic design, it stands out as an excellent choice for anyone looking to tackle their outdoor cutting tasks effectively. Its thoughtful design and technology make it a worthy investment for both homeowners and professional users.