Poulan 161608 owner manual Assemble Gauge Wheels to Mower Deck See Fig, Check Brake System

Page 8

ASSEMBLY

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 5)

The gauge wheels are designed to keep the mower deck in proper posi- tion when operating mower. Be sure they are properly adjusted to ensure

optimum mower performance.

•Assemble gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be as- sembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 17/32 washer, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjust- ments section of this manual.

GAUGE

WHEEL

MOUNTING

BRACKET

3/8-16

 

LOCKNUT

17/32 WASHER

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

FIG. 5

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” on page 3 of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

CHECKLIST

BEFOREYOU OPERATE AND ENJOYYOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROMTHIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly prepared and charged. (Minimum 1 hour at 6 amps).

✓Seat is adjusted comfortably and tightened securely.

✓All tires are properly inflated. (For shipping purposes, the tires were over- inflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

✓Before driving tractor, be sure freewheel control is in drive position.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls - their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓It is important to purge the transmission before operating your tractor for the first time. Follow proper starting and transmission purging instructions (See “TO START ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual).

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model NO. HD145H42G Turn off blades when not mowing Safe Operation Practices for Ride-On MowersMow only in daylight or good artificial light Do not use grass catcher on steep slopesProduct Specifications Customer ResponsibilitiesModel NUMBERHD145H42G Serial Number Date of PurchaseAdjustments BatteryMower Adjustment MowerContents of Hardware Pack Tools Required for Assembly To Remove Tractor from CAR- TONBefore Rolling Tractor OFF Skid Unpack CartonHOW to SET UP Your Tractor Connect Battery See FigsInstall Seat See Fig Adjust seat before tightening adjustment boltAssemble Gauge Wheels to Mower Deck See Fig Check Brake SystemCheck Tire Pressure Check Deck LevelnessBattery Reverse Forward Fast UnlockedLock Locked Reverse Neutral High LOW Hydro Models onlyKnow Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills Before Starting the Engine Check Engine OIL Level See FigADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionLubrication Chart Service DatesGeneral Recommendations Before Each USEBattery TractorBrake Operation TiresEngine BeltsTransaxle Cooling Transaxle Pump FluidClean AIR Screen See a Service air cleaner more often under dusty conditionsAIR Filter See a Engine OIL Filter See BCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower See Fig To Remove Mower See FigRaise mower to its highest position To Level Mower HousingSIDE-TO-SIDE Adjustment See Figs To Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig Block up axle securelyTo Start Engine with a Weak Battery See Fig To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Carburetor See FigPreliminary Setting Final SettingTroubleshooting Points OFF Schematic Because of THIS,Tractor - Model Number HD145H42G ElectricalKEY Part Description Harness Eng B&S 14 OHV DualChassis and Enclosures 159530 Chassis Wldmt 140356 Drawbar Stretch 17490612 7418051274780616 19131312Drive 140607 Steering Assembly 140044 1927201610040600 124035X Support Shaft 126684XSeat Assembly Wheels and Tires LBD48LSB42 LAO18Engine Muffler Exhaust LT B&S 14HP IC OHV Lift Wire Asm Inner W/Plunger 159460139868 Arm Suspension Rear 3146R Retainer Spring 140302 73540600 Nut Crownlock 3/8-24Mower Deck Washer 17/32 x 15/16 x 12 Gauge 137729 Screw Hex Thd CutWasher Hard Blade Mower Vented Transaxle Hydro Gear Model Number 142986 Housing, Lower 150778 75 x 1.25 x20 x 142937 Swashplate, Variable 142965 PinService Notes Service Notes Service Department Canada contactBox Orangeburg, SC 29116 USAThis OUT Dotted Lines Slope Only Ride UP and Down HillCUT

161608 specifications

The Poulan 161608 chainsaw is a robust tool designed for homeowners and professionals alike, offering a blend of power, efficiency, and user-friendly features. This chainsaw is part of Poulan’s line of reliable outdoor power equipment, making it an excellent choice for tackling various cutting tasks, from trimming branches to felling small trees.

One of the main features of the Poulan 161608 is its powerful engine. It is equipped with a 38cc 2-stroke gas engine, which provides ample power for demanding cutting applications. The engine is designed for durability and reliability, ensuring that users can rely on the chainsaw for a range of tasks without frequent breakdowns. Additionally, the engine is engineered for easy starting, thanks to the incorporation of a primer bulb and an adjustable choke system. This allows users to start the chainsaw effortlessly, even in colder weather conditions.

The Poulan 161608 also boasts a 16-inch bar and chain, providing a balance between maneuverability and cutting capacity. The length of the blade makes it suitable for a variety of jobs, whether you are pruning trees, cutting firewood, or performing light logging tasks. The chain is designed for quick and efficient cutting, ensuring that users can accomplish their tasks with minimal effort.

Safety is a priority for Poulan, and this chainsaw features a chain brake that helps protect the user by stopping the chain in case of kickback. The front handguard and rear handle are ergonomically designed for a secure grip, reducing fatigue during extended use. Furthermore, the anti-vibration technology integrated into the design helps absorb shock, providing increased comfort and control when operating the chainsaw.

Maintenance is made easy with the Poulan 161608, as it features an automatic oiling system that ensures the chain remains lubricated, reducing wear and tear and extending the life of the chainsaw. Additionally, the tool-less chain tensioning system allows users to easily adjust the chain without the need for additional tools, making it more convenient for on-the-go maintenance.

In summary, the Poulan 161608 is a powerful and efficient chainsaw that combines user-friendly features, safety mechanisms, and ease of maintenance. With its robust engine, reliable cutting performance, and ergonomic design, it stands out as an excellent choice for anyone looking to tackle their outdoor cutting tasks effectively. Its thoughtful design and technology make it a worthy investment for both homeowners and professional users.
Top Page Image Contents