Poulan 2001-03 operating instructions Safety Notice Exposure to, Back toward the operator

Page 5

and bar as original equipment. Repairs on a chain brake should be made by an autho- rized servicing dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

S Tip contact in some cases may cause a lightning fast reverse REACTION, kicking the guide bar up and back toward the oper- ator.

SPinching the saw chain along the top of the guide bar may push the guide bar rapidly

back toward the operator.

SEither of these reactions may cause you to lose control of the saw which could result in serious injury.Do not rely exclusively upon the safety devices built into your saw.

NOTE: If this saw is to be used for commer- cial logging, a chain brake is required and shall not be removed or otherwise disabled to comply with Federal OSHA Regulations for Commercial Logging. Contact your Au- thorized Service Dealer or call 1--800--554--6423.

SAFETY NOTICE: Exposure to

vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

SPECIAL NOTICE: Your saw is equipped with a temperature limiting muffler and spark arresting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines to be equipped with a spark arresting screen. If you operate a chain saw in a state or locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. Refer to the SERVICE section for maintenance of the spark arresting screen.

STANDARDS: This saw is listed by Un- derwriter’s Laboratories, Inc., in accordance with American National Standards for Gaso- line--Powered Chain Saw Safety Require- ments (ANSI B175.1-1991).

Failure to follow all Safety Rules and Precau- tions can result in serious injury. If situations occur which are not covered in this manual, use care and good judgement. If you need

assistance, contact your Authorized Service Dealer or call 1-800--554--6723.

Protective gloves (not provided) should be worn during assembly.

ATTACHING THE BAR & CHAIN (If not

already attached)

WARNING: If received assembled, repeat all steps to ensure your saw is prop- erly assembled and all fasteners are secure. Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not moving!

SLoosen and remove the chain brake nuts and the chain brake from the saw.

S Remove the plastic shipping spacer (if present).

Location of shipping spacer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chain Brake

Chain Brake

Nuts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bar Tool

SAn adjusting pin and screw is used to ad- just the tension of the chain. It is very im- portant when assembling the bar, that the pin located on the adjusting screw aligns into a hole in the bar. Turning the screw will move the adjustment pin up and down the screw. Locate this adjustment before you begin mounting the bar onto the saw (see illustration).

Inside view of

Chain Brake

Adjustment located on Chain Brake

S Turn the adjusting screw counterclock- wise to move the adjusting pin almost as far as it will go to the rear. This should allow the pin to be near the correct position. Fur- ther adjustment may be necessary as you mount the bar.

SMount the bar as illustrated.

SSlide the bar toward the rear of the saw as far as possible.

SPrepare the chain by checking the proper direction. Without following the illustration it is easy to place the chain on the saw in the wrong direction. Use the illustration of the chain to determine the proper direc- tion.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 2250 / 2450 / 2550 LE Series For Occasional Use Only Operate Your SAW Safely Plan AheadMaintain Your SAW in Good Working Order Handle Fuel with CautionReduce the Chance Kickback KickbackMaintain Control Ward the operatorChain Brake Kickback Safety FeaturesBack toward the operator Safety Notice Exposure toAdjusting the tension Know Your SAW ON/STOP SwitchThrottle Trigger Throttle LockoutFueling Engine Switch Primer BulbBAR and Chain Lubrication Important Points to RememberBack Starting a Warm EngineImportant Points Felling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Plan a clear retreat pathCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points Using a support standLimbing PruningCarburetor Adjustments Cleaning the Spark ARREST- ING ScreenAIR Filter Inspect Muffler and Spark Arresting ScreenChain Sharpening BAR MaintenanceIgnition Timing Spark PlugTroubleshooting Table Cause Remedy Placement and Repair of Emission

2001-03 specifications

The Poulan 2001-03 model is a significant entry in the line of outdoor power equipment, particularly known for its robust design and advanced features that cater to both homeowners and landscaping professionals. This model is primarily recognized for its versatility in handling a variety of tasks such as trimming, pruning, and cutting, making it an excellent choice for those with diverse lawn care needs.

One of the standout features of the Poulan 2001-03 is its powerful engine. Equipped with a reliable two-cycle engine, this model offers efficient performance that ensures effective cutting speed and power. This engine design not only provides substantial power but also contributes to a lightweight construction, allowing for greater maneuverability and ease of use during extended periods of operation.

The Poulan 2001-03 is characterized by its ergonomic handle design, which is aimed at enhancing user comfort and control. The handle is adjustable, helping users of different heights to find an optimal working position. Additionally, the inclusion of anti-vibration technology helps reduce fatigue during use, making it suitable for longer tasks without compromising comfort.

Another key characteristic of this model is its innovative cutting system. The Poulan 2001-03 features a dual-line trimmer head, which allows for more efficient cutting of grass and weeds. The ability to easily reload the trimmer line and adjust the cutting width adds to the convenience, making it user-friendly for both novice and experienced operators.

Durability is also a notable aspect of the Poulan 2001-03. Built with high-quality materials, this model can withstand the rigors of frequent use. It also boasts a fuel-efficient design, helping users save on operational costs while minimizing emissions – a testament to the company’s commitment to environmental sustainability.

In conclusion, the Poulan 2001-03 model stands out due to its powerful engine, ergonomic design, innovative cutting system, and durability. These features collectively make it an efficient and reliable choice for anyone looking to maintain their outdoor spaces effectively. Whether for residential use or in a professional landscaping capacity, the Poulan 2001-03 is equipped to handle a variety of tasks with ease and efficiency.
Top Page Image Contents