Poulan 952711612, 115261026 instruction manual Chain Replacement, To Replace Chain

Page 12

File Holder

File

WARNING: Maintain the proper hook angle according to the manufacturer’s specifica- tions for the chain you are using. Improper hook

Cutter

90˚

angle will increase the chance of kickback which can result in serious injury.

Depth Gauge

SAlign the 30˚ file holder marks parallel with the bar and to the center of the chain.

Cutter

30˚

Cutter

File Holder Line

 

SSharpen cutters on one side of the chain first. File from the inside of each cutter to the outside. Then, turn the chain saw around and repeat the process for the other side of the chain.

SFile on the forward stroke only. Use 2 or 3 strokes per cutting edge.

SKeep all cutters the same length when

filing.

SFile enough to remove any damage to cutting edges (side plate and top plate of cutter).

All Cutters

Remove Damage

Same Length

 

 

Top Plate

 

Side Plate

SFile chain to meet the specifications as shown.

75˚

60˚

30˚

 

Hook Angle

 

 

0.025 inch

 

(0.65 mm)

 

Rounded

Right

Corner

 

Too Much Hook Angle

Squared Off

 

Corner

Wrong

 

4. Check and lower depth gauges.

Depth Gauge Tool

File

Depth Gauge

SPlace gauge tool on cutter.

SIf the depth gauge is higher than the depth gauge tool, file it level to the top of the depth gauge tool.

SMaintain rounded front corner of depth gauge with a flat file.

NOTE: The very top of the depth gauge should be flat with the front half

rounded off with a flat file.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

CHAIN REPLACEMENT

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

It is normal for a new chain to stretch during the first 15 minutes of operation. You should re- check your chain tension frequently and adjust the chain tension as required. See CHAIN TEN- SION section. Replace the old chain when it be- comes worn or damaged. Use only the Low- Kickback replacement chain specified in the repair parts list.

TO REPLACE CHAIN:

1.Move ON/STOP switch to the STOP posi- tion and disconnect spark plug (or discon- nect powerhead from power source).

2.Remove bar clamp nut.

3.Remove bar clamp.

4.Turn adjusting screw by hand counter- clockwise until adjusting pin just touches the stop.

5.Slide guide bar behind sprocket until guide bar stops against sprocket.

6.Remove the old chain.

7.Carefully remove new chain from pack- age. Hold chain with the drive links as shown.

Cutter

Tip of

Bar

Drivelink

CUTTERS MUST FACE IN

DIRECTION OF ROTATION

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules Do not smoke or allow smoking near fuel or the powerheadPlan Ahead Mix and pour fuel outdoorsUNIT/MAINTENANCE Safety Operate Your Pruner SafelyKickback Safety Features KickbackReduce the Chance Kickback Maintain ControlAssembly Installing Pruner ATTACH- MentTransporting and Storage Tools RequiredShoulder Strap Assembly Adjusting the Assist HandleOperation Installing Attachment Hanger BAR and Chain LubricationOperating Position Pruning Important PointsMaintenance Inspect and Clean Unit and DecalsCheck for Damaged or Worn Parts Check for Loose Fasteners and PartsService and Adjustments Chain Replacement To Replace ChainChain Adjustment User Replaceable Service PartsSeasonal Storage Limited Warranty Statesville RoadCanada, contact

115261026, 952711612 specifications

The Poulan 952711612 and 115261026 represent two of the most proficient trimmer heads in Poulan’s extensive lineup, known for their reliability and performance in lawn maintenance. Both models are designed to optimize the efficiency of string trimmers, catering to the needs of both casual gardeners and professional landscapers.

One of the standout features of the Poulan 952711612 is its advanced design, which allows for easy line loading. This innovative design not only saves time during setup but also enhances the overall user experience by reducing frustration during maintenance. The 952711612 utilizes a dual-line system that increases productivity by cutting a wider swath of grass with each pass, making it ideal for tackling larger areas of overgrowth.

In addition, the Poulan 115261026 boasts a similar dual-line feature, but it is particularly noted for its bump feed mechanism. This technology permits the user to feed additional line simply by tapping the bottom of the trimmer head against the ground. This hands-free operation is invaluable for maintaining continuous workflow, especially when trimming around edges and in hard-to-reach spots.

Both models are constructed with durable materials, ensuring long-lasting performance even when subjected to demanding conditions. The robust design minimizes wear and extends the lifespan of the trimmer heads, making them a worthwhile investment for any user. The trimmer heads are lightweight, which reduces fatigue during use, allowing for prolonged periods of trimming without discomfort.

Moreover, compatibility is key for these models. The Poulan 952711612 and 115261026 are designed to fit a variety of Poulan trimmers, ensuring that users don't have to worry about purchasing additional equipment. This versatility is coupled with an easy installation process, making the transition from old trimmer heads seamless and hassle-free.

Overall, the Poulan 952711612 and 115261026 embody the brand’s commitment to delivering quality lawn care products. With user-friendly features, durable construction, and innovative technology, they serve as reliable tools for achieving a well-manicured lawn. Whether for routine yard work or tackling tougher landscaping jobs, these trimmer heads stand out as excellent choices in the outdoor power equipment market.
Top Page Image Contents