Poulan 115261026, 952711612 instruction manual Shoulder Strap Assembly, Adjusting the Assist Handle

Page 7

Locking/Release

Button in Primary Hole

SHOULDER STRAP ASSEMBLY

WARNING: Proper shoulder strap and handle adjustments are required before use. The shoulder strap clamp must be installed as shown above the assist handle on the upper shaft (powerhead end of unit).

NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are pro- vided to adapt this attachment for use with pow- erheads that have a 1″ diameter upper shaft (the shoulder strap clamp will not tighten down securely on the 1″ diameter upper shaft without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for powerheads with a 7/8″ upper shaft.

LOWER SHOULDER STRAP CLAMP

Spacer Tabs

Spacer Tabs positioned for use on 1″ diameter upper shaft

1.Place the upper shoulder strap clamp over the upper shaft above the handlebar.

2.Position the lower shoulder strap clamp under the upper shaft and align the upper and lower clamp screw holes (use spacer tabs between upper and lower clamps if necessary to secure clamp, i.e. for 1″ di- ameter upper shaft).

3.Insert two screws into the screw holes.

4.Secure shoulder strap clamp by tighten- ing screws with the hex wrench.

5.Try on shoulder strap and adjust for fit and balance before starting the engine or begin- ning a cutting operation.

6.Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right

side of your waist.

NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the shoulder.

7.Adjust the strap, allowing the hook to be about 3 -- 6 inches (8 -- 15 cm) below the waist.

8.Fasten the strap hook to the upper clamp and lift the tool to the operating position.

Shoulder Strap

Shoulder

Strap

Clamp

ADJUSTING THE ASSIST HANDLE

WARNING: When adjusting the as- sist handle, be sure it remains directly above the coupler on the engine end shaft to ensure proper balancing of unit.

Assist Handle

Coupler

Upper Shoulder

Strap Clamp

POWERHEAD

END

Lower Shoulder

ATTACHMENT

END

Strap Clamp

Screws

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Mix and pour fuel outdoors Safety RulesDo not smoke or allow smoking near fuel or the powerhead Plan AheadOperate Your Pruner Safely UNIT/MAINTENANCE SafetyMaintain Control Kickback Safety FeaturesKickback Reduce the Chance KickbackTools Required AssemblyInstalling Pruner ATTACH- Ment Transporting and StorageAdjusting the Assist Handle Shoulder Strap AssemblyOperation Pruning Important Points Installing Attachment HangerBAR and Chain Lubrication Operating PositionCheck for Loose Fasteners and Parts MaintenanceInspect and Clean Unit and Decals Check for Damaged or Worn PartsService and Adjustments To Replace Chain Chain ReplacementUser Replaceable Service Parts Chain AdjustmentSeasonal Storage Statesville Road Limited WarrantyCanada, contact

115261026, 952711612 specifications

The Poulan 952711612 and 115261026 represent two of the most proficient trimmer heads in Poulan’s extensive lineup, known for their reliability and performance in lawn maintenance. Both models are designed to optimize the efficiency of string trimmers, catering to the needs of both casual gardeners and professional landscapers.

One of the standout features of the Poulan 952711612 is its advanced design, which allows for easy line loading. This innovative design not only saves time during setup but also enhances the overall user experience by reducing frustration during maintenance. The 952711612 utilizes a dual-line system that increases productivity by cutting a wider swath of grass with each pass, making it ideal for tackling larger areas of overgrowth.

In addition, the Poulan 115261026 boasts a similar dual-line feature, but it is particularly noted for its bump feed mechanism. This technology permits the user to feed additional line simply by tapping the bottom of the trimmer head against the ground. This hands-free operation is invaluable for maintaining continuous workflow, especially when trimming around edges and in hard-to-reach spots.

Both models are constructed with durable materials, ensuring long-lasting performance even when subjected to demanding conditions. The robust design minimizes wear and extends the lifespan of the trimmer heads, making them a worthwhile investment for any user. The trimmer heads are lightweight, which reduces fatigue during use, allowing for prolonged periods of trimming without discomfort.

Moreover, compatibility is key for these models. The Poulan 952711612 and 115261026 are designed to fit a variety of Poulan trimmers, ensuring that users don't have to worry about purchasing additional equipment. This versatility is coupled with an easy installation process, making the transition from old trimmer heads seamless and hassle-free.

Overall, the Poulan 952711612 and 115261026 embody the brand’s commitment to delivering quality lawn care products. With user-friendly features, durable construction, and innovative technology, they serve as reliable tools for achieving a well-manicured lawn. Whether for routine yard work or tackling tougher landscaping jobs, these trimmer heads stand out as excellent choices in the outdoor power equipment market.
Top Page Image Contents