Filing instructions, Oregon 91P chain | Oregon 91P F&B A107038

Filing instructions, Oregon® 91P chain

FILE SIZE: Use a 5/32” round file and file guide.

	TOP-PLATE		TOP-PLATE
DEPTH-GAUGE SETTING:	CUTTING ANGLE:	SIDE-PLATE ANGLE:	FILING ANGLE:	FILE-GUIDE ANGLE:

*See warning and note below

	50°	85°
Heel	.025”	30°	90°
down			90°
down

WARNING	Failure to follow filing instructions can
	increase the level of kickback which

can result in severe injury to the saw operator or bystanders.

Do not exceed the depth-gauge setting shown above

Always file depth gauges back to their original rounded or ramped shape after lowering

Oregon® 91P meets the reduced-kickback requirements of ANSI B175.1 when tested on a representative sample of chainsaws. This chain significantly reduces the risk of chainsaw kickback while maintaining high cutting performance. ALL CUTTING CHAIN CAN KICK BACK, WHICH MAY RESULT IN SEVERE INJURY TO THE SAW OPERATOR OR BYSTANDERS. Users should be cautioned to operate their saw safely, and to read and follow all warnings in their saw operator’s manual and Oregon® 91P chain-maintenance instructions.

91P Chain maintenance tools

DESCRIPTION	PACK	PART NUMBER
Assembled File Guide, 5/32”	Each	37534
Round Files, 5/32”	12-pack	70504
	2-pack	40459
Depth-gauge Tool	10-pack	22290
Flat File	12-pack	12211

DESCRIPTION

1/8” Thick Grinding Wheels (3.2mm):

Full-size, 5 3/4” dia.

(For use with 511A grinders)

Mini Grinder Wheels, 4 1/8” dia.

(For use with 108181 mini grinders)

PACK PART NUMBER

5-pack OR534-18

Each OR534-18A

5-pack OR4125-18

Each OR4125-18A

91P Chain replacement parts

	LEFT-HAND	RIGHT-HAND		PRESET		NOTCHED BUMPER
CHAIN TYPE	CUTTER	CUTTER	TIE STRAP	TIE STRAP	DRIVE LINK	DRIVE LINK
91P	P111807	P111808	P111616	P112320	P28298	P111822

NOTE: Individual parts packages contain 25 pieces.

What’s the difference between a 3/8”-pitch chain,

and a low-profile 3/8”-pitch chain?

Standard 3/8”-pitch chains are full-size professional-type chains intended for

use on medium to large gasoline-powered saws, 3.0 to 6.0 cu. in. (50-100cc).

Low-profile 3/8” chains have the same pitch, but there are differences in the

drive sprockets and bar-nose sprockets used with low-profile chains. Standard
3/8” chains and low-profile 3/8” chains are NOT interchangeable. The phrase	DEFINITION	3/8”-PITCH CHAIN (72V)	LOW-PROFILE 3/8”-
“low profile” refers to the height, measured from the bar’s rail to the top of the	DEFINITION	3/8”-PITCH CHAIN (72V)	LOW-PROFILE 3/8”-
	OF PITCH	STANDARD PROFILE	PITCH CHAIN (91P)

cutter. On low-profile chains, the height is less than on standard chains. Low-

profile 3/8”-pitch chains are intended for use on electric saws, and small gasoline-powered saws up to 2.5 cubic inches (41cc).

Other Oregon® low-profile 3/8”-pitch (91) cutting chains

PART NO.	DESCRIPTION, TYPES OF USE
91VG	Low-kickback Chamfer Chisel™ chain for cutting clean wood with electric and small gasoline chainsaws up to 2.5 cu. in. (41cc)
91VS	A professional Chamfer Chisel™ chain for experienced users of small chainsaws who prefer a low-profile 3/8”-pitch chain.
M91VS	A specialized version of 91VS with extra-heavy-duty chrome plating to cut effectively in extremely dirty, abrasive conditions.

Because every

cut counts

For more information on these and other Oregon® products, contact your authorized Oregon® distributor, or:

OREGON CUTTING SYSTEMS DIVISION, BLOUNT, INC. PO Box 22127 • Portland, OR, U.S.A. 97269-2127 Phone: 503- 653-8881 Fax: 503-653-4201 http://www.oregonchain.com

IN CANADA: OREGON DISTRIBUTION LTD. 505 Edinburgh Rd. N. • Guelph, Ontario, Canada N1H 6L4

Phone: 519-822-6870 Fax: 519-822-4999 http://www.oregonchain.ca	Printed in USA PFS 91P A107038 AA 0903