RIDGID WD1665 manual Cleaning Vac Filter, Wet/Dry Vac

Page 12

Maintenance (continued)

6.Replace foam pad holder on blower with the tabs away from the blower. Reinstall foam pad under the tabs of the holder.

7.Reinstall intake shield and 3 screws. The unit is ready for use.

Cleaning Vac Filter

Your filter should be cleaned often to main- tain peak vac performance.

Be sure to dry the filter before storing or picking up dry debris.

IMPORTANT: After cleaning, check the fil- ter for tears or small holes. Do not use a fil- ter with holes or tears in it. Even a small hole can cause a lot of dust to come out of your vac. Replace it immediately.

NOTE: The filter is made of high quality paper designed to stop very small particles of dust. The filter can be used for wet or dry pick up. Handle the filter carefully when removing to clean or installing it. Creases in the filter pleats may occur from installation but will not affect the performance of the fil- ter.

Removal

To remove the filter for cleaning or replace- ment, unscrew the filter nut from the filter cage, remove filter plate and lift off filter.

IMPORTANT: To avoid damage to the blower wheel and motor, always reinstall the filter before using the vac for dry material pickup.

CAUTION: Do not remove the filter cage or float. It is there to shut off air- flow when the drum is full of liquids.

Dry Filter

1.Light cleaning of some dry debris can be accomplished without removing the filter from the vac. Simply slap your hand on top of the lid while the vac is turned off.

2.Clean the filter in an open area. Clean- ing SHOULD be done outdoors and not in the living quarters.

3.Remove filter from vac. Gently tap the fil- ter against the inside wall of your dust drum and the debris will loosen and fall.

4.For thorough cleaning of dry filter with fine dust (no debris) you may run water through it as described under “Wet Filter”.

Wet Filter

Remove filter from vac, run water through the filter from a hose or spigot. Take care that water pressure from the hose is not strong enough to damage filter. Remember: To dry a filter quickly, reinstall the filter on the vac and allow the unit to run for 10 min- utes. The clean air rushing through the filter will dry it.

Installation

Refer to “Filter Assembly”.

Allow the filter to dry before reinstalling and storing the vac.

Wet/Dry Vac

To keep your Wet/Dry Vac looking its best, clean the outside with a cloth dampened with warm water and mild soap.

To clean the drum:

1.Dump out debris.

2.Wash drum thoroughly.

3.Wipe out with dry cloth.

WARNING: To assure product SAFETY and RELIABILITY, repairs and adjustment should be performed by Authorized Service Centers, always using RIDGID replacement parts.

NOTE: To quiet noisy casters put a drop of oil on the roller shaft.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents WD1665 Table of Contents Page Unpacking and Checking Carton Contents IntroductionFloat/Cage Assembly Filter Assembly/ReplacementAccessory Caddy/Caster Assembly Caster/Caster Foot AssemblyTo Store Your Accessories Caster Caster Stem Caster Ball Foot Dust DrumVac Assembly Positioning Detachable Blower Power Head AssemblyDrum Drum Latch Drum Lip Inlet Lid Assembly Dust Drain Cap Operation Press Pull Release ButtonVacuuming Dry Materials Vacuuming LiquidsEmptying Dust Drum Blowing Feature Cord WrapMoving the Vac Handle Pull Handle Cord WrapMaintenance Assemble the Detachable Blower for BlowingBlower Intake Cleaning Vac Filter Wet/Dry VacWet Nozzle Latches Nozzle Body Removable InsertRepair Parts Servicing of DOUBLE-INSULATED WET/DRY VACKey Description 818961 Spacer Repair Parts Questions or COMMENTS? EmersonManual DEL Usuario Para su seguridadIndice Palabras de señal de seguridadArtículo El riesgo de incendio, sacudidas eléctricas o lesionesGuarde Estas Instrucciones Introducción Nota ImportantePor favor, léala cuidadosamente Clave DescripciónEnsamblaje del flotador/jaula Ensamblaje/reemplazo de un filtroEnsamblaje de la base portaaccesorios y las ruedecillas Para almacenar los accesoriosTambor RuedecillaEnsamblaje de la aspiradora Reborde del tambor EntradaPestillo del Ensamblaje de la tapaFuncionamiento AdvertenciaRecogida de materiales secos con la aspiradora Vaciado del tambor para polvoRecogida de líquidos con la aspiradora Funcionamiento continuación Enrollador del cordónTransporte de la aspiradora Dispositivo de sopladoMantenimiento Ensamblaje del soplador desmontable para soplarEntrada del soplador Mantenimiento continuación Boquilla para mojado PestillosAccesorio de Piezas de repuesto MOJADO/SECO CON Aislamiento DobleNúmero de modelo WD16650 ClavePiezas de repuesto ¿PREGUNTAS O COMENTARIOS? No. de catálogo WD1665 No. de modelo WD16650 Número de serie

WD1665 specifications

The RIDGID WD1665 is a powerful and versatile wet/dry vacuum designed to handle a variety of clean-up tasks, making it an essential tool for both home and professional use. It boasts a robust 16-gallon capacity, allowing users to tackle larger jobs without the need for constant emptying. This vacuum's impressive size is complemented by its powerful 6.5 horsepower motor, which delivers strong suction power, making it effective at picking up both wet and dry debris.

One of the standout features of the WD1665 is its innovative filtration system. It comes equipped with a RIDGID proprietary fine-dust filter that efficiently captures fine particles, ensuring cleaner air is released back into the environment. Moreover, this filter can be easily cleaned and is reusable, which not only saves on replacement costs but also promotes sustainability.

The vacuum is designed with user convenience in mind. It features a lock-on hose that securely attaches to the vacuum, preventing any accidental disconnections during use. The 7-foot locking hose is highly flexible and durable, allowing for extensive reach in various cleaning scenarios. With multiple attachments included, such as a crevice tool and a utility nozzle, users can easily adapt the vacuum to suit different surfaces and cleaning tasks.

For enhanced maneuverability, the RIDGID WD1665 is built with a sturdy cart and large rear wheels, making it easy to transport over various terrains. The vacuum also features a top carry handle, simplifying lifting and relocation. Additionally, the power cord is a generous 20 feet long, providing ample reach without the hassle of frequent unplugging.

Durability is another key characteristic of the RIDGID WD1665. Constructed with high-quality materials, this vacuum is built to withstand regular use across various environments, from job sites to home workshops. Its rugged design ensures it remains reliable even in tough conditions.

In summary, the RIDGID WD1665 is a high-capacity wet/dry vacuum that combines powerful suction, advanced filtration, and user-friendly features, making it a top choice for anyone looking to efficiently manage debris and maintain a clean workspace. Its combination of performance, durability, and practicality makes it an indispensable tool for carpenters, contractors, and homeowners alike.
Top Page Image Contents