Scag Power Equipment SWU manual Mower Operation, Use gasoline with an octane rating no less than

Page 10

9.Always store gasoline in a safety-approved, red container.

10.Be careful when servicing the battery as it con- tains acid, which is corrosive and could cause burns to skin and clothing.

11.Batteries release explosive gases when being charged or discharged. Keep batteries away from any source of sparks and/or flame.

INITIAL RUN-IN PROCEDURES (FIRST DAY OF USE OR APPROXIMATELY 10 HOURS)

1.Check the belts for proper tension at 2, 4 and 8 hours. Check for abnormal wear and adjust as needed.

2.Check the steering control rods for neutral adjustment. (See Adjustments, page 7)

3.Check the tires for proper pressure.

Caster Wheels

25 psi.

Drive Wheels

15 psi.

4.Check for loose hardware. Tighten as needed.

5.Check the safety switches for proper adjustment: * The engine will crank, but not start if the

machine is not in neutral.

*On electric start machines, the engine will not crank if the PTO switch is on.

*The engine should crank and start if the machine is in neutral and the PTO engagement switch is OFF.

6.Apply lubricant to all the grease fittings. Lubricant was applied at the factory. This is just a precautionary check to make sure that all the fittings have been lubricated properly.

MOWER OPERATION

1.Read and understand the safety instructions before attempting to operate this machine.

2.Before starting the engine:

*Check the oil level in the engine.

*Fill the fuel tank with clean, fresh, lead-free gasoline.

*Open the fuel valve on the bottom of the fuel tank.

-NOTE-

Use gasoline with an octane rating no less than 87.

*The transmission must be in NEUTRAL.

*The blade clutch switch must be in the OFF position.

*The operator's presence levers must be released.

*The neutral latches must be in the neutral lock position.

*The key switch must be on.

3.Start the engine:

*Choke as required. If the engine is cold, pull the choke knob out. When the engine starts, slowly push the choke in. If the engine stalls, repeat the above operation. When the engine is warm, choking may not be necessary.

4.Engage the cutter blades by pulling the blade clutch switch into the ON position. Push the switch to the OFF position to disengage the cutter blades.

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

390S0138

6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Illustrated Parts List Introduction Signal Words General Safety InstructionsISO Symbols Fast Slow Do not operate where conditions are slippery Before Operating While OperatingMaintenance and Storage Falling Hazard USE only Scag Approved Riding AttachmentsMower Operation Use gasoline with an octane rating no less thanTransmission Drive Belt Drive Control Adjustments Cutter Deck Belt AdjustmentsADJUST-A-GRIP Settings Adjusting Cutting Height Cutter BladesLubrication & Maintenance Mobilux #2 Mobil service stationsTroubleshooting Cutting Conditions Condition Cause CureUneven Cut on Flat Scalping Blades Technical Specifications EngineCutter Deck Page Cutter Deck Ref. Part No. Number Description 48 & 52 Cutter Decks Part Description Deck Frame Ref. Part No. No. Description 48 & 52 Deck Frame Tire Valve, Purchase Locally Engine Deck Wire Harness Adaptor, 17KA Handle Assembly 15KA 17KA Instrument Panel For Reference Only Order Parts from Peerless / Tecumseh REF. Part NO. no DescriptionHandle Wire Harness Manual Start Wire Harness Adapter / Kawasaki 481863 Heavy-Duty Commercial 1 2 3 4 Limited Warranty Commercial Equipment 2000

SWU specifications

Scag Power Equipment, a leading manufacturer in the outdoor power equipment industry, has established a reputation for its commitment to quality, performance, and innovation. One of their standout products is the SWU series, known for its durability and advanced technology designed to meet the demands of landscape professionals and serious homeowners alike.

The Scag SWU series is best known for its robust construction and superior mowing capabilities. Built with a heavy-duty steel frame, these mowers ensure long-lasting performance even under the toughest conditions. The SWU is equipped with a powerful engine, typically a commercial-grade Kohler or Vanguard engine, providing unparalleled power and efficiency. This means users can tackle larger lawns and more demanding terrain without the fear of stalling or bogging down.

One of the key features of the SWU series is its exceptional cutting technology. The mower's precision-engineered cutting deck is designed to deliver a smooth, even cut for a pristine finish. The deck height can be easily adjusted to suit various mowing needs, allowing for versatility in handling different grass types and conditions. Scag's proprietary blade design further enhances cutting performance, allowing users to efficiently mulch or bag grass clippings.

The SWU series also prioritizes user comfort and ease of operation. Ergonomically designed controls put everything within easy reach, ensuring a more enjoyable mowing experience. The seating is plush and adjustable, reducing fatigue during extended usage. Additionally, the SWU incorporates advanced vibration damping technology which minimizes operator fatigue, making it easier to handle large mowing tasks.

Maintenance is made simple with Scag's thoughtful design. The SWU features easy-access points that allow operators to check fluids, clean the deck, and perform routine maintenance without hassle. This not only prolongs the life of the mower but also keeps it operating at peak performance.

In summary, Scag Power Equipment's SWU series combines strength, precision, and user-friendly features to set a high standard in the mowing industry. With its powerful engines, advanced cutting technology, and focus on operator comfort, the SWU provides professional results for users seeking efficiency and reliability in their lawn care arsenal. Whether for commercial applications or residential use, the SWU series is a valuable addition to any landscaping toolkit.
Top Page Image Contents