Scag Power Equipment STWC52V-25KA, STWC61V-26KA-LC, STWC52V-26KA-LC Custom-Cut Baffle Adjustment

Page 30

R

Section 6

3.Check the cutter deck cutting height by placing the lanyard pin in the 3" position on the cutting height index. Release the deck from the transport position and allow the deck to move to the 3" cutting height position.

4.Check the measurement from the floor to the cutter blade tip. If the measurement is not at 3", an adjustment can be made using the deck height control rod. See Figure 6-6.

- NOTE -

If an adjustment had to be made, be sure that the cutter deck can easily be locked into the transport position.

6.7 Custom-Cut Baffle Adjustment

The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut. The baffle can be set in three (3) (early models), or seven (7) (current production) different positions for optimum performance.

3-Position Custom-Cut Baffle Adjustment - EARLY MODELS

A.3" Position - (See Figure 6-8). Baffle is installed using the top set of holes on the front baffle welded inside the cutter deck. In this position the Velocity-Plus cutter deck will deliver the best quality-of-cut in very tall, wiry, tough to cut grass.

B.3-1/2" Position - (See Figure 6-8). Baffle is installed using the middle set of holes on the front baffle welded inside the cutter deck. Can be used for general purpose cutting. Placing the Custom-Cut Baffle in the 3-1/2" position gives a good mix of cutting performance in all types of grass.

C.4" Position (factory setting) - (See Figure 6-8). Baffle is installed using the bottom set of holes on the front baffle welded inside the cutter deck. Placing the baffle in the 4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

To adjust the Custom-Cut Baffle height:

1.Place the cutter deck in the transport position.

2.Remove the hardware securing the Custom-Cut Baffle to the cutter deck. See Figure 6-8.

- NOTE -

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.

3.Move the Custom-Cut Baffle to desired position. See Figure 6-8.

4.Reinstall the mounting hardware as shown. Torque hardware to 39 lb-ft.

7-Position Custom-Cut Baffle Adjustment - CURRENT PRODUCTION

A.3-1/2" or 3-3/4" Position - (See Figure 6-9). For very tall, wiry or tough-to-cut grass.

B.4" (factory setting), 4-1/4" or 4-1/2" Position - (See Figure 6-9). For general purpose cutting.This gives the best mix of cutting performance in all types of grass.

C.4-3/4" or 5-1/4" Position - (See Figure 6-9). Placing the baffle in either the 4-3/4" or 5-1/4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

To adjust the Custom-Cut Baffle height:

1.Place the cutter deck in the transport position.

2.Remove the hardware securing the Custom-Cut Baffle to the cutter deck.

- NOTE -

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.

3.Move the Custom-Cut Baffle to desired position. See Figure 6-9.

4.Reinstall the mounting hardware. Torque hardware to 39 lb-ft.

26

Page 29 Page 31
Image 30
Page 29 Page 31
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Adjustments Inside Back CoverDirection Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsSymbols Symbol DescriptionSafety Information Signal WordsBefore Operation Considerations Operation Considerations Section Roll-Over Protection System Foldable Roll-over protection system if equippedFoldable Roll-Over Protection System Maintenance Considerations & Storage Safety And Instructional Decals Install Belt COvER BeforeEngine SpecificationsPower Head ElectricalHydraulic System Weights And Dimensions 52V 61VCutter Deck Productivity 52VOperating Instructions Controls And Instrument IdentificationSafety Interlock System Initial Run-In ProceduresStarting The Engine Ground Travel And SteeringForward Travel Engaging The Deck Drive Cutter Blades Reverse TravelAfter Operation Hillside OperationParking The Mower Removing Clogged MaterialAdjusting Cutting Height Moving Mower With Engine StoppedRecommendations For Mowing Adjusting The Steering Levers Towing Optional Hitch AccessoryTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment Tracking AdjustmentBelt Alignment Throttle Control And Choke AdjustmentsBelt Adjustment Cutter Deck Adjustments Cutter Deck LevelAdjustment ROD Lock NUT Cutter Deck Pitch Cutter Deck HeightCustom-Cut Baffle Adjustment Position Custom-Cut Baffle Adjustment Early ModelsPosition Custom-Cut Baffle Adjustment Current Production Position Custom-Cut Baffle Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemEngine Air Cleaner Cleaning and/or Replacing Air Cleaner ElementReplacing In-Line Fuel Filter Elements Battery Charging the BatteryJump Starting Cutter Blades Blade ReplacementDrive Belts Blade InspectionLiquid-Cooled Machines Only TiresCooling System Checking Coolant LevelCleaning the Radiator Debris Screen Body, Deck, And UpholsterySection Illustrated Parts List Scag Approved Attachments And Accessories52V Cutter Deck Description 61V Cutter Deck 424367 Dust Shield 483210 Idler Pulley, 5 Dia Cutter Deck Controls Rod End, 1/2-20 Female LH Thread Sheet Metal Components Seat Assembly w/Adj. Rails & Seat Belt Stwc ROLL-OVER Protection System Retractable Seat Belt Drive System Components 424137 Bracket Engine and Attaching Parts Engine and Attaching Parts Steering Components Section Brake Components Brake Components Fuel and Hydraulic System Fuel and Hydraulic System Electrical System Kohler & Kawasaki AIR-COOLED Key Assembly w/Fob Electrical System 26HP Kawasaki LIQUID-COOLED 483629 Fuse Holder Hydraulic Pump Assembly Housing Kit Replacement Decals and Information Plates Install Belt COvER Before482166R Stwc 2007 RDP2 Electrical Schematic Kohler & Kawasaki AIR-COOLED Electrical Schematic 26HP Kawasaki LIQUID-COOLED Section Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Notas Refrigerante del nivel del Verificación .A RadiadorDel desechos de criba la de Limpieza .B Comprimido aire usar al seguridad de gafasCuchilla la de Reemplazo 9-7 Figura Tapicería Y Plataforma CuerpoLlantas Para apropiada protección la lleve Siempre Cuchillas las de Afilado .BTransmisión DE Correas Cuchilla la de Reemplazo .CBatería Puente por Arranque .BBatería la de Carga .A Batería ED Electrolito Para Auxilios PrimerosMotor DEL Aire DE Filtro Aire de filtroDel elemento del reemplazo y/o Limpieza .A Motor del combustible de filtro del Ubicación 7-7 FiguraMotor del aceite de filtro de Cambio .C Combustible de tanque del Llenado .AMotor DEL Combustible DE Sistema Cárter del aceite de Cambio .BHidráulico aceite de nivel del Verificación .A Hidráulico aceite de Depósito 2-7 FiguraHidráulico aceite de Cambio .B Hidráulico SistemaConexión de puntos de Lubricación 1.7 Figura Lubricación ObservacionesProcedimiento 500 200 100 Primeros Observaciones Procedimiento 500 100 Recomendados Servicio DE Intervalos Mantenimiento DE TablaSuciedad o polvo InicialCorte de deflector del Posición .9-6 Figura De personalizadoCorte de deflector del Posición .10-6 Figura Personalizado corte de Deflector .8-6 FiguraCorte de plataforma la de Altura CorteCorte de plataforma la de Ajuste .4-6 Figura Corte de plataforma la de InclinaciónCorte de plataforma la de Nivel Corte DE Plataforma LA DE AjustesCorrea LA DE Alineación Advertencia Correa LA DE AjusteEstrangulación Y Aceleración DE Controles LOS DE Austes De control de varilla la de Ajuste .3-6 Figura Neutral AjusteDirección Desplazamiento DE AjustesEstacionamiento DE Freno DEL AjusteFreno de varilla la de Ajuste .2-6 Figura Solución Causa Condición Irregular La de ancho loInclinadas Salientes Perfil o voladoCortar sin césped Corte deTrayectorias entre La en cortarDirección de palancas las de Ajuste Equipo del peso El .cuestas en remolque NuncaLa de liberación de Palanca 4-4 Figura Opcional enganche de accesorio RemolquePlataforma Corte DE Altura LA DE AjusteCésped EL DetenidoOperación LA DE Después Cortacéspedes Cuesta UNA EN Operación DEL Estacionamiento Reversa en Desplazamiento Adelante hacia DesplazamientoCorte DE Cuchillas Plataforma DE Transmisión LA DE Conexión Uso de día Primer Inicial Motor DEL ArranqueHoras 20 aproximadamente Arranque DE ProcedimientosDescarga de válvula la de control de Palancas Seguridad DE Bloqueo DE SistemaPlataforma la de elevación de pie de Palanca De fusibles Dos .1-4 Figura PortafusiblesIdentificación Instrumentos E Controles Cortacésped del plataforma la de InterruptorContinuación Tractor ProductividadHidráulico Sistema Corte DE PlataformaEléctrico Sistema MotorTractor Seguridad DE Y Instructivas Calcomanías Almacenamiento Y Mantenimiento DE Consideraciones Seguridad de cinturón del Inspección Rops del Bisagra 2-2 FiguraVuelco Contra Protección DE Sistema Vuelco contra protección de plegable Sistema 1-2 FiguraOperación DE Consideraciones ContinuaciónAdvertencia Operación LA a Previas Consideraciones Señalización DE PalabrasSeñalización de Palabra Lento Rápido ISO Símbolos Instrucciones DE Referencia IntroducciónMantenimiento 7 Sección Ajustes 6 SecciónPágina Tema Seguridad de Información 2 Sección Operación de Instrucciones 4 SecciónEspecificaciones 3 Sección General Información 1 Sección25KA-STWC52V Equipo del almacenamientoManual DEL Operador
Related manuals
Manual 34 pages 10.91 Kb

STWC61V-25KA-LC, STWC61V-27CV, STWC52V-26KA-LC, STWC61V-26KA-LC, STWC52V-25KA specifications

Scag Power Equipment is a renowned name in the commercial and residential landscaping industry, and its STWC series stands out for exceptional performance and reliability. The STWC52V-26KA-LC, STWC61V-25KA-LC, STWC52V-25KA, STWC61V-26KA-LC, and STWC61V-27CV models exemplify the brand’s commitment to quality and innovation, providing operators with high-performance solutions for lawn care and maintenance.

One of the primary features of these models is their robust engine options. Designed with powerful Kawasaki or Kohler engines, these mowers deliver impressive horsepower, enabling efficient cutting performance across various terrains. The STWC series is engineered for durability, with a heavy-duty steel chassis that withstands the rigors of professional use while providing stability and support.

A critical characteristic of these mowers is their cutting deck options, offered in different sizes such as 52 and 61 inches. They feature a precision-engineered deck design that ensures a clean, even cut, reducing the need for multiple passes. The high-performance blades are made from hardened steel, maintaining their sharpness longer and enhancing cutting efficiency.

In addition to their cutting capabilities, the STWC series incorporates advanced technology for ease of operation and comfort. These models are equipped with ergonomic control panels, allowing operators to easily adjust speed and cutting height. The adjustable cutting height ensures adaptability to different grass conditions, providing versatility in landscaping projects.

Technologically, the STWC mowers utilize a fully hydraulic drive system, providing smooth and responsive maneuverability. This feature enhances the machines' ability to navigate tight corners and obstacles, making them ideal for residential lawns and commercial properties alike. Operators can enjoy precise control and increased productivity, thanks to the intuitive handling.

Moreover, these models prioritize user comfort with features such as padded seat designs, vibration-dampening systems, and easy access to controls. The suspension seats are not only comfortable for prolonged use but also help reduce operator fatigue, allowing for extended work hours without discomfort.

In summary, the Scag Power Equipment STWC mowers combine powerful engines, durable construction, and advanced technological features to deliver outstanding performance. Their design is tailored for professionals seeking reliable, efficient, and user-friendly equipment for all landscaping tasks, making them a solid investment in maintaining pristine outdoor spaces. Whether for commercial or residential use, these mowers are sure to exceed expectations.
Top Page Image Contents