Scag Power Equipment STWC52V-25KA manual General Information, Introduction, Direction Reference

Page 5

Section 1

R

GENERAL INFORMATION

1.1 Introduction

Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual.

If additional information or service is needed, contact your Scag Power Equipment Dealer.

We encourage you to contact your dealer for repairs. All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts.

- IMPORTANT -

The replacement of any part on this product by other than the manufacturer's authorized replacement part may adversely affect the performance, durability or safety of this product.

Use of other than original Scag replacement parts will void the warranty.

When ordering parts, always give the model and serial number of your mower. The serial number plate is located under the seat where shown in Figure 1-1.

SERIAL NUMBER

PLATE LOCATION

S C A G

Power Equipment

Model

Serial

USE ONLY SCAG APPROVED ATTACHMENTS AND ACCESSORIES.

Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine. See Section 8-1.

WARNING

For pictorial clarity, some illustrations and figures in this manual may show shields, guards or plates open or removed. Under no circumstances should your mower be operated without these devices in place.

All information is based upon product information available at the time of approval for printing. Scag Power Equipment reserves the right to make changes at any time without notice and without incurring any obligation.

1.2 Direction Reference

The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s right and left when seated in the normal operating position and facing the forward travel direction.

1.3Servicing the Engine and Drive Train Components

The detail servicing and repair of the engine, hydraulic pumps and gearboxes are not covered in this manual; only routine maintenance and general service instructions are provided. For service of these components during the limited warranty period, it is important to contact your Scag dealer or find a local authorized servicing agent of the component manufacturer. Any unauthorized work done on these components during the warranty period may void your warranty.

STC 2001 SPL-1

Figure 1-1. Mower Serial Number Plate Location

1

Image 5
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Inside Back Cover AdjustmentsIntroduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsSymbol Description SymbolsBefore Operation Considerations Safety InformationSignal Words Operation Considerations Section Foldable Roll-over protection system if equipped Roll-Over Protection SystemFoldable Roll-Over Protection System Maintenance Considerations & Storage Install Belt COvER Before Safety And Instructional DecalsPower Head SpecificationsEngine ElectricalCutter Deck Weights And Dimensions 52V 61VHydraulic System Productivity 52VControls And Instrument Identification Operating InstructionsInitial Run-In Procedures Safety Interlock SystemForward Travel Starting The EngineGround Travel And Steering Reverse Travel Engaging The Deck Drive Cutter BladesParking The Mower Hillside OperationAfter Operation Removing Clogged MaterialRecommendations For Mowing Adjusting Cutting HeightMoving Mower With Engine Stopped Towing Optional Hitch Accessory Adjusting The Steering LeversCondition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Travel Adjustments AdjustmentsParking Brake Adjustment Tracking Adjustment Neutral AdjustmentBelt Adjustment Cutter Deck Adjustments Throttle Control And Choke AdjustmentsBelt Alignment Cutter Deck LevelCutter Deck Pitch Cutter Deck Height Adjustment ROD Lock NUTPosition Custom-Cut Baffle Adjustment Current Production Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment Early Models Position Custom-Cut Baffle Adjustment Maintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilReplacing In-Line Fuel Filter Elements Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Jump Starting BatteryCharging the Battery Drive Belts Blade ReplacementCutter Blades Blade InspectionCooling System TiresLiquid-Cooled Machines Only Checking Coolant LevelBody, Deck, And Upholstery Cleaning the Radiator Debris ScreenSection Scag Approved Attachments And Accessories Illustrated Parts List52V Cutter Deck Description 61V Cutter Deck 424367 Dust Shield 483210 Idler Pulley, 5 Dia Cutter Deck Controls Rod End, 1/2-20 Female LH Thread Sheet Metal Components Seat Assembly w/Adj. Rails & Seat Belt Stwc ROLL-OVER Protection System Retractable Seat Belt Drive System Components 424137 Bracket Engine and Attaching Parts Engine and Attaching Parts Steering Components Section Brake Components Brake Components Fuel and Hydraulic System Fuel and Hydraulic System Electrical System Kohler & Kawasaki AIR-COOLED Key Assembly w/Fob Electrical System 26HP Kawasaki LIQUID-COOLED 483629 Fuse Holder Hydraulic Pump Assembly Housing Kit Install Belt COvER Before Replacement Decals and Information Plates482166R Stwc 2007 RDP2 Electrical Schematic Kohler & Kawasaki AIR-COOLED Electrical Schematic 26HP Kawasaki LIQUID-COOLED Section Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Notas Del desechos de criba la de Limpieza .B RadiadorRefrigerante del nivel del Verificación .A Comprimido aire usar al seguridad de gafasLlantas Cuchilla la de Reemplazo 9-7 FiguraTapicería Y Plataforma Cuerpo Transmisión DE Correas Cuchillas las de Afilado .BPara apropiada protección la lleve Siempre Cuchilla la de Reemplazo .CBatería la de Carga .A Puente por Arranque .BBatería Batería ED Electrolito Para Auxilios PrimerosDel elemento del reemplazo y/o Limpieza .A Aire de filtroMotor DEL Aire DE Filtro Motor del combustible de filtro del Ubicación 7-7 FiguraMotor DEL Combustible DE Sistema Combustible de tanque del Llenado .AMotor del aceite de filtro de Cambio .C Cárter del aceite de Cambio .BHidráulico aceite de Cambio .B Hidráulico aceite de Depósito 2-7 FiguraHidráulico aceite de nivel del Verificación .A Hidráulico SistemaConexión de puntos de Lubricación 1.7 Figura Procedimiento 500 200 100 Primeros LubricaciónObservaciones Suciedad o polvo Recomendados Servicio DE Intervalos Mantenimiento DE TablaObservaciones Procedimiento 500 100 InicialCorte de deflector del Posición .10-6 Figura De personalizadoCorte de deflector del Posición .9-6 Figura Personalizado corte de Deflector .8-6 FiguraCorte Corte de plataforma la de AlturaCorte de plataforma la de Nivel Corte de plataforma la de InclinaciónCorte de plataforma la de Ajuste .4-6 Figura Corte DE Plataforma LA DE AjustesEstrangulación Y Aceleración DE Controles LOS DE Austes Correa LA DE AlineaciónAdvertencia Correa LA DE Ajuste Dirección Neutral AjusteDe control de varilla la de Ajuste .3-6 Figura Desplazamiento DE AjustesFreno de varilla la de Ajuste .2-6 Figura EstacionamientoDE Freno DEL Ajuste Solución Causa Condición Inclinadas Salientes La de ancho loIrregular Perfil o voladoTrayectorias entre Corte deCortar sin césped La en cortarEquipo del peso El .cuestas en remolque Nunca Dirección de palancas las de AjustePlataforma Opcional enganche de accesorio RemolqueLa de liberación de Palanca 4-4 Figura Corte DE Altura LA DE AjusteOperación LA DE Después Césped ELDetenido Cortacéspedes Cuesta UNA EN Operación DEL Estacionamiento Corte DE Cuchillas Plataforma DE Transmisión LA DE Conexión Reversa en DesplazamientoAdelante hacia Desplazamiento Horas 20 aproximadamente Motor DEL ArranqueUso de día Primer Inicial Arranque DE ProcedimientosPlataforma la de elevación de pie de Palanca Seguridad DE Bloqueo DE SistemaDescarga de válvula la de control de Palancas De fusibles Dos .1-4 Figura PortafusiblesCortacésped del plataforma la de Interruptor Identificación Instrumentos E ControlesHidráulico Sistema ProductividadContinuación Tractor Corte DE PlataformaTractor Eléctrico SistemaMotor Seguridad DE Y Instructivas Calcomanías Almacenamiento Y Mantenimiento DE Consideraciones Rops del Bisagra 2-2 Figura Seguridad de cinturón del InspecciónVuelco contra protección de plegable Sistema 1-2 Figura Vuelco Contra Protección DE SistemaContinuación Operación DE ConsideracionesAdvertencia Señalización de Palabra Operación LA a Previas ConsideracionesSeñalización DE Palabras Lento Rápido ISO Símbolos Introducción Instrucciones DE ReferenciaPágina Tema Mantenimiento 7 SecciónAjustes 6 Sección Especificaciones 3 Sección Operación de Instrucciones 4 SecciónSeguridad de Información 2 Sección General Información 1 SecciónEquipo del almacenamiento 25KA-STWC52VManual DEL Operador
Related manuals
Manual 34 pages 10.91 Kb

STWC61V-25KA-LC, STWC61V-27CV, STWC52V-26KA-LC, STWC61V-26KA-LC, STWC52V-25KA specifications

Scag Power Equipment is a renowned name in the commercial and residential landscaping industry, and its STWC series stands out for exceptional performance and reliability. The STWC52V-26KA-LC, STWC61V-25KA-LC, STWC52V-25KA, STWC61V-26KA-LC, and STWC61V-27CV models exemplify the brand’s commitment to quality and innovation, providing operators with high-performance solutions for lawn care and maintenance.

One of the primary features of these models is their robust engine options. Designed with powerful Kawasaki or Kohler engines, these mowers deliver impressive horsepower, enabling efficient cutting performance across various terrains. The STWC series is engineered for durability, with a heavy-duty steel chassis that withstands the rigors of professional use while providing stability and support.

A critical characteristic of these mowers is their cutting deck options, offered in different sizes such as 52 and 61 inches. They feature a precision-engineered deck design that ensures a clean, even cut, reducing the need for multiple passes. The high-performance blades are made from hardened steel, maintaining their sharpness longer and enhancing cutting efficiency.

In addition to their cutting capabilities, the STWC series incorporates advanced technology for ease of operation and comfort. These models are equipped with ergonomic control panels, allowing operators to easily adjust speed and cutting height. The adjustable cutting height ensures adaptability to different grass conditions, providing versatility in landscaping projects.

Technologically, the STWC mowers utilize a fully hydraulic drive system, providing smooth and responsive maneuverability. This feature enhances the machines' ability to navigate tight corners and obstacles, making them ideal for residential lawns and commercial properties alike. Operators can enjoy precise control and increased productivity, thanks to the intuitive handling.

Moreover, these models prioritize user comfort with features such as padded seat designs, vibration-dampening systems, and easy access to controls. The suspension seats are not only comfortable for prolonged use but also help reduce operator fatigue, allowing for extended work hours without discomfort.

In summary, the Scag Power Equipment STWC mowers combine powerful engines, durable construction, and advanced technological features to deliver outstanding performance. Their design is tailored for professionals seeking reliable, efficient, and user-friendly equipment for all landscaping tasks, making them a solid investment in maintaining pristine outdoor spaces. Whether for commercial or residential use, these mowers are sure to exceed expectations.