Scag Power Equipment STWC operating instructions Seat Belt Inspection

Page 11

Section 2

This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Do not mow on wet grass. Wet grass reduces traction and steering control.

Any or all parts of the Roll Over Protection System MUST NOT be removed. Failure to adhere to this guideline could result in injury or death.

The potential exposure of this seat belt to severe enviromental conditions make it crucial to inspect the seat belt system regularly.

It is recommended that the seat belt be inspected on a daily basis for signs of damage. Any seat belt system that shows cuts, fraying, extreme or unusual wear, significant discoloration due to UV exposure, dirt or stiffness, abrasion to the seat belt webbing, or damage to the buckle, latch plate, hardware or any other obvious problem should be replaced immediately.

WARNING:

Failure to properly inspect and maintain the seat belt can cause serious injury or loss of life.

1.Check the full length of the seat belt webbing for cuts, wear, fraying, dirt and stiffness. See Figure 2-1.

2.Check the seat belt webbing in areas exposed to ultra violet rays from the sun or extreme dust or dirt. If the original color of the webbing in these areas is extremely faded and/or is packed with dirt, the physical strength of this webbing may have deteriorated. If this condition exists, replace the seat belt system.

3.Check the buckle and latch for proper operation and determine if the latch plate is exessively worn, deformed, or of the buckle is damaged or cracked. See Figure 2-1.

INSPECT BUCKLE & LATCH

INSPECT WEBBING

Figure 2-1 Seat Belt Inspection

WARNING:

Reduce speed when turning, operating on slopes, slick or wet surfaces. Allow extra distance to stop.

Stay off of slopes too steep for safe operation. To check a slope, attemp to back up it (with the cutter deck down). If the machine can not back up the slope without the wheels slipping, do not operate the machine on this slope.

ALWAYS travel up or down the slope whenever possible. Never across the slope.

DO NOT mow near drop-offs, ditches or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge caves in.

Operate the machine smoothly, no sudden turns, starts or stops on a slope.

NEVER tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control.

DO NOT permit untrained personnel to operate the machine.

7

Page 10 Page 12
Image 11
Page 10 Page 12
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Servicing the Engine and Drive Train Components General InformationIntroduction Direction ReferenceISO Symbols CE Mark Fast Slow Signal Word Safety InformationSignal Words This symbol means Attention! Become Alert! YourOperation Considerations Before Operation Considerations ContdRoll Over Protection System Operation Considerations ContdSeat Belt Inspection Stwc With Roll Over Protection System Maintenance Considerations & StorageSafety and Instructional Decals Tractor SpecificationsEngine ElectricalProductivity Tractor ContdCutter Deck Hydraulic SystemControls and Instrument Identification Ignition Switch -1. Used to startOperating Instructions Right Steering Control -1. Used to Safety Interlock SystemForward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Hillside OperationRecommendations for Mowing Adjusting Cutting HeightRemoving Clogged Material Moving Mower with Engine StoppedDeck Release Lever Towing optional hitch accessoryCondition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Contd Condition Cause Cure Ground Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Alignment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AdjustmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Custom-Cut Baffle AdjustmentCustom-Cut Baffle Hours MaintenanceMaintenance Chart Recommended Service Intervals Break-In 100 200 500 Procedure Comments FirstProcedure Comments Break-In 100 200 500 First Maintenance Chart Recommended Service Intervals ContdLubrication Grease Fitting Lubrication Chart see Figure Lubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine OIL Engine Fuel SystemFuel Filter Engine AIR CleanerCleaning and/or Replacing Air Cleaner Element BatteryJump Starting Charging the BatteryBattery Electrolyte First AID Blade Inspection Blade ReplacementDrive Belts Cutter BladesBODY, DECK, and Upholstery TiresSection 52A 52A Cutter Deck 61A Cutter Deck Ref. Part No. No. Description Cutter Deck Controls Part Description Sheet Metal Components Sheet Metal Components Stwc Roll Over Protection System Flatwasher, 1/2-.562 x 1.375 x Drive System Components Drive System Components Engine and Attaching Parts Part Description 33A 29, 29A Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Commercial 482166R SC 2004 RDP2 Electrical Schematic Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Mientras equipo del parte ninguna lave No LlantasCuchilla la de Reemplazo 10-7 Figura Comprimido Aire use motor el lave No .caliente estáCuchillas las de Afiliado 9-7 Figure Cuchillas las de Afiliado .BPara apropiada protección la lleve Siempre Cuchilla la de Reemplazo .CBatería DE Electrolito Para Auxilios Primeros Puente por Arranque .BBatería la de Carga .A Motor DEL Aire DE Filtro BateríaAire de filtro Motor DEL Aceite Combustible de tanque del Llenado .AMotor DEL Combustible DE Sistema Hidráulico Sistema Hidráulico aceite de Depósito 2-7 FiguraHidráulico aceite de Cambio .B Hidráulico aceite de nivel el Verificar .AConexión de puntos de Lubricación 1.7 Figura Observaciones Procedimiento 500 200 100 Accesorios DE Lubricación DE Tabla LubricaciónHoras MantenimientoRecomendados Servicio DE Intervalos Mantenimiento DE Tabla Suciedad o polvoPersonalizado corte de Deflector .7-6 Figura PersonalizadoPosiciones 3 tres en colocar puede se deflector El Corte de plataforma la de AlturaCorte de plataforma la de Inclinación Corte de plataforma la de NivelCorte DE Plataforma LA DE Ajustes Alineación de Ajuste Correa LA DE AlineaciónCorrea LA DE Ajuste Estrangulación Y Aceleración DE Controles LOS DE AjustesDirección de control de varillas de Ajuste .3-6 Figura Neutral AjusteDesplazamiento DE Ajustes Freno de Ajuste .1-6 Figura AjustesEstacionamiento DE Freno DEL Ajuste Freno de varilla la de Ajuste .2-6 FiguraSolución Causa Condición Solución Causa Condición Continuación Fallas DE Solución La en cortar sin césped Corte de trayectoriasEntre cortar sin césped De Franjas VetasEquipo del peso El .cuestas en remolque Nunca Opcional Enganche de accesorio RemolqueCorte de altura de Ajuste 5-4 Figura Atascado Material DEL Retiro Corte DE Altura LA DE AjusteCésped EL Cortar Para Recomendaciones Detenido Motor EL CON Cortacésped DEL DesplazamientoCuesta UNA EN Operación CortacéspedDEL Estacionamiento Reversa en Desplazamiento Corte DE Cuchillas Plataforma DE Transmisión LA DE ConexiónArranque DE Procedimientos DirecciónMotor DEL Arranque Horas 10 aproximadamente Uso de día Primer InicialDe número el Indica .1-4 Figura Horómetro Seguridad DE Bloqueo DE SistemaUsado .1-4 Figura corte de altura la de Ajuste De fusibles Dos .1-4 Figura PortafusiblesCortacésped del plataforma la de Interruptor Operación DE InstruccionesInstrumentos E Controles DE Identificación Continuación Tractor ProductividadCorte DE Plataforma Motor EspecificacionesTractor Eléctrico SistemaSeguridad DE Y Instructivas Calcomanías Almacenamiento Y Mantenimiento DE Consideraciones Inmediatamente reemplazar debe se obvio Seguridad de cinturón del Inspección 1-2 FiguraOperación DE Consideraciones ContinuaciónVuelco Contra Protección DE Sistema Continuación Operación LA a Previas ConsideracionesIntroducción Peligro Seguridad DE InformaciónOperación LA a Previas Consideraciones Señalización DE PalabrasDescripción Símbolo ISO Símbolos Instrucciones DE Referencia General InformaciónAjustes 6 Sección Continuación Contenido DE TablaRepuesto de Piezas 8 Sección Mantenimiento 7 SecciónGeneral Información 1 Sección Contenido DE Tabla27CV-STWC61AaA5600001 99999 Desde serie de números con61A-SMWCaA5700001 99999 52A-SMWCaA5500001 99999Manualdeloperador

STWC specifications

The Scag Power Equipment STWC, or the Scag Turf Tiger Walk Behind Mower, is a powerful and durable machine designed for the professional landscaper and serious lawn care enthusiast. Known for its robust construction and high-performance capabilities, the STWC provides exceptional cutting efficiency and versatility in various mowing conditions.

One of the standout features of the STWC is its industrial-grade engine options. With choices ranging from EFI to air-cooled variants, users benefit from superior power and fuel efficiency. The mower's engine options ensure that operators can tackle tough mowing tasks with confidence. The STWC is equipped with a high-capacity fuel tank, allowing for extended run times, making it ideal for larger properties or commercial applications.

The STWC features Scag's proprietary Hydro-Gear transmission system, which provides smooth operation and excellent maneuverability. This system allows for precise speed control and helps reduce operator fatigue. Additionally, the mower's heavy-duty steel frame and mower deck contribute to its durability, ensuring it can withstand the rigors of professional use. The cutting deck is available in various sizes, accommodating individual preferences and mowing requirements.

Ergonomic design is a hallmark of the STWC, ensuring comfort during extended hours of operation. The handlebars are adjustable to suit different operator heights, and the soft-touch grips minimize vibration, enhancing user comfort. The mower also features commercial-grade components, including high-performance blades and a high-efficiency air filtration system, which contribute to a cleaner cutting performance.

Another noteworthy characteristic is the mower's versatility. The STWC can be equipped with various accessories and attachments, such as grass catchers, mulch kits, and even spreaders, allowing users to customize their mower for a range of tasks. This adaptability makes it an excellent choice for both residential and commercial landscaping needs.

In terms of maintenance, the STWC is designed for ease, with quick-access components and simple service points. Regular maintenance can be performed conveniently, ensuring the machine remains in peak operating condition.

Overall, the Scag Power Equipment STWC stands out as a high-performance walk-behind mower that combines power, durability, and versatility. Its innovative technologies and thoughtful design make it a preferred choice among professionals who demand reliability and excellent cutting results. Whether for home use or commercial landscaping, the STWC promises a superior mowing experience.
Top Page Image Contents