Scag Power Equipment STWC operating instructions Hillside Operation, Parking the Mower

Page 20

Section 4

3.To disengage the deck drive, push the switch in to the disengage position.

4.Always operate the engine at full throttle to properly maintain cutting speed. If the engine starts to lug down, reduce the forward speed and allow the engine to operate at maximum RPM.

4.7 HILLSIDE OPERATION

WARNING:

DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. ALWAYS FOLLOW OSHA APPROVED OPERATION.

1.This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Wet grass reduces traction and steering control. The Roll Over Protection System is standard equipment for this machine. See Section 2.5, page 7 of this manual for further details.

2.To prevent tipping or loss of control, do not start or stop suddenly, avoid unnecessary turns and travel at reduced speed. If tires loose traction, disengage blades and proceed slowly off the slope.

3.Avoid sudden starts when mowing uphill. Sudden starts may cause the machine to tip backwards.

4.Loss of traction may occur when traveling down hill. Weight transfers to the front of the machine and may cause the drive wheels to slip causing loss of braking or steering.

5.Keep tires properly inflated.

park the machine on an incline.

2.Place the steering control levers in the neutral position.

3.Disengage the cutter blades.

4.Slow the engine to idle speed.

5.Engage the parking brake.

6.Turn the ignition key to the OFF position and remove the key.

4.9 AFTER OPERATION

1.Wash the entire mower after each use. Do not use high pressure spray or direct the spray onto electrical components.

-IMPORTANT-

Do not wash a hot or running engine. Cold water will damage the engine. Use compressed air to clean the engine if it is hot.

2.Keep the entire mower clean to inhibit serious heat damage to the engine or hydraulic oil circuit.

3.Check the drive belts for proper alignment and any signs of wear. Correct and adjust if necessary.

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

4.After the mower has cooled down, fill the fuel tanks with fresh, clean fuel at the end of every day of operation. See Engine Owner's Manual for proper octane requirements.

5.Check the tire pressure. Adjust pressure if necessary.

4.8 PARKING THE MOWER

1. Park the machine on a flat, level surface only. Do not

16

Image 20
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd General Information IntroductionDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Safety Information Signal WordsThis symbol means Attention! Become Alert! Your Signal WordBefore Operation Considerations Contd Operation ConsiderationsOperation Considerations Contd Roll Over Protection SystemSeat Belt Inspection Maintenance Considerations & Storage Stwc With Roll Over Protection SystemSafety and Instructional Decals Specifications EngineElectrical TractorTractor Contd Cutter DeckHydraulic System ProductivityControls and Instrument Identification Ignition Switch -1. Used to startOperating Instructions Safety Interlock System Right Steering Control -1. Used toForward Travel Starting the EngineGround Travel and Steering Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Parking the MowerAdjusting Cutting Height Removing Clogged MaterialMoving Mower with Engine Stopped Recommendations for MowingTowing optional hitch accessory Deck Release LeverTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Ground Adjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentTracking Adjustment Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Custom-Cut Baffle Adjustment Cutter Deck HeightCustom-Cut Baffle Maintenance Maintenance Chart Recommended Service IntervalsBreak-In 100 200 500 Procedure Comments First HoursProcedure Comments Break-In 100 200 500 First Maintenance Chart Recommended Service Intervals ContdLubrication Grease Fitting Lubrication Chart see Figure Lubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Fuel System Engine OILEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner ElementBattery Fuel FilterJump Starting Charging the BatteryBattery Electrolyte First AID Blade Replacement Drive BeltsCutter Blades Blade InspectionTires BODY, DECK, and UpholsterySection 52A 52A Cutter Deck 61A Cutter Deck Ref. Part No. No. Description Cutter Deck Controls Part Description Sheet Metal Components Sheet Metal Components Stwc Roll Over Protection System Flatwasher, 1/2-.562 x 1.375 x Drive System Components Drive System Components Engine and Attaching Parts Part Description 33A 29, 29A Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Commercial 482166R SC 2004 RDP2 Electrical Schematic Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Llantas Cuchilla la de Reemplazo 10-7 FiguraComprimido Aire use motor el lave No .caliente está Mientras equipo del parte ninguna lave NoCuchillas las de Afiliado .B Para apropiada protección la lleve SiempreCuchilla la de Reemplazo .C Cuchillas las de Afiliado 9-7 FigureBatería DE Electrolito Para Auxilios Primeros Puente por Arranque .BBatería la de Carga .A Motor DEL Aire DE Filtro BateríaAire de filtro Motor DEL Aceite Combustible de tanque del Llenado .AMotor DEL Combustible DE Sistema Hidráulico aceite de Depósito 2-7 Figura Hidráulico aceite de Cambio .BHidráulico aceite de nivel el Verificar .A Hidráulico SistemaConexión de puntos de Lubricación 1.7 Figura Accesorios DE Lubricación DE Tabla Lubricación Observaciones Procedimiento 500 200 100Mantenimiento Recomendados Servicio DE Intervalos Mantenimiento DE TablaSuciedad o polvo HorasPersonalizado Personalizado corte de Deflector .7-6 FiguraCorte de plataforma la de Altura Posiciones 3 tres en colocar puede se deflector ElCorte de plataforma la de Inclinación Corte de plataforma la de NivelCorte DE Plataforma LA DE Ajustes Correa LA DE Alineación Correa LA DE AjusteEstrangulación Y Aceleración DE Controles LOS DE Ajustes Alineación de AjusteDirección de control de varillas de Ajuste .3-6 Figura Neutral AjusteDesplazamiento DE Ajustes Ajustes Estacionamiento DE Freno DEL AjusteFreno de varilla la de Ajuste .2-6 Figura Freno de Ajuste .1-6 FiguraSolución Causa Condición Solución Causa Condición Continuación Fallas DE Solución Corte de trayectorias Entre cortar sin céspedDe Franjas Vetas La en cortar sin céspedEquipo del peso El .cuestas en remolque Nunca Opcional Enganche de accesorio RemolqueCorte de altura de Ajuste 5-4 Figura Corte DE Altura LA DE Ajuste Césped EL Cortar Para RecomendacionesDetenido Motor EL CON Cortacésped DEL Desplazamiento Atascado Material DEL RetiroCuesta UNA EN Operación CortacéspedDEL Estacionamiento Corte DE Cuchillas Plataforma DE Transmisión LA DE Conexión Reversa en DesplazamientoDirección Motor DEL ArranqueHoras 10 aproximadamente Uso de día Primer Inicial Arranque DE ProcedimientosSeguridad DE Bloqueo DE Sistema Usado .1-4 Figura corte de altura la de AjusteDe fusibles Dos .1-4 Figura Portafusibles De número el Indica .1-4 Figura HorómetroCortacésped del plataforma la de Interruptor Operación DE InstruccionesInstrumentos E Controles DE Identificación Continuación Tractor ProductividadCorte DE Plataforma Especificaciones TractorEléctrico Sistema MotorSeguridad DE Y Instructivas Calcomanías Almacenamiento Y Mantenimiento DE Consideraciones Seguridad de cinturón del Inspección 1-2 Figura Inmediatamente reemplazar debe se obvioOperación DE Consideraciones ContinuaciónVuelco Contra Protección DE Sistema LA a Previas Consideraciones Continuación OperaciónPeligro Seguridad DE Información Operación LA a Previas ConsideracionesSeñalización DE Palabras IntroducciónDescripción Símbolo ISO Símbolos General Información Instrucciones DE ReferenciaContinuación Contenido DE Tabla Repuesto de Piezas 8 SecciónMantenimiento 7 Sección Ajustes 6 SecciónContenido DE Tabla General Información 1 SecciónDesde serie de números con 61A-SMWCaA5700001 9999952A-SMWCaA5500001 99999 27CV-STWC61AaA5600001 99999Manualdeloperador

STWC specifications

The Scag Power Equipment STWC, or the Scag Turf Tiger Walk Behind Mower, is a powerful and durable machine designed for the professional landscaper and serious lawn care enthusiast. Known for its robust construction and high-performance capabilities, the STWC provides exceptional cutting efficiency and versatility in various mowing conditions.

One of the standout features of the STWC is its industrial-grade engine options. With choices ranging from EFI to air-cooled variants, users benefit from superior power and fuel efficiency. The mower's engine options ensure that operators can tackle tough mowing tasks with confidence. The STWC is equipped with a high-capacity fuel tank, allowing for extended run times, making it ideal for larger properties or commercial applications.

The STWC features Scag's proprietary Hydro-Gear transmission system, which provides smooth operation and excellent maneuverability. This system allows for precise speed control and helps reduce operator fatigue. Additionally, the mower's heavy-duty steel frame and mower deck contribute to its durability, ensuring it can withstand the rigors of professional use. The cutting deck is available in various sizes, accommodating individual preferences and mowing requirements.

Ergonomic design is a hallmark of the STWC, ensuring comfort during extended hours of operation. The handlebars are adjustable to suit different operator heights, and the soft-touch grips minimize vibration, enhancing user comfort. The mower also features commercial-grade components, including high-performance blades and a high-efficiency air filtration system, which contribute to a cleaner cutting performance.

Another noteworthy characteristic is the mower's versatility. The STWC can be equipped with various accessories and attachments, such as grass catchers, mulch kits, and even spreaders, allowing users to customize their mower for a range of tasks. This adaptability makes it an excellent choice for both residential and commercial landscaping needs.

In terms of maintenance, the STWC is designed for ease, with quick-access components and simple service points. Regular maintenance can be performed conveniently, ensuring the machine remains in peak operating condition.

Overall, the Scag Power Equipment STWC stands out as a high-performance walk-behind mower that combines power, durability, and versatility. Its innovative technologies and thoughtful design make it a preferred choice among professionals who demand reliability and excellent cutting results. Whether for home use or commercial landscaping, the STWC promises a superior mowing experience.