Remington Power Tools 100271-01 owner manual Felling Procedure, Limbing a Tree

Page 10

OPERATING CHAIN SAW

Continued

Felling Procedure

Felling Notch

A properly placed felling notch will determine direction tree will fall. Place felling notch on side of tree in direction you want tree to fall (see Figure 13). Follow directions below to create a felling notch.

1.Make lower notch cut as close to ground as possible. Hold saw so guide bar is horizontal. Cut 1/3 the diameter of tree trunk (see Figure 13). Note: Always make this horizontal lower notch cut first. If you make this cut second, tree can pinch chain or guide bar.

2.Start upper notch cut the same distance above first cut as first cut is deep.

Example: If lower notch cut is 20 centimeters deep, start upper notch cut 20 centimeters above it. Cut downward at 45° angle. The upper notch cut should meet end of lower notch cut (see Figure 13).

3.Remove tree trunk wedge created by notching cuts.

Felling Cut

1.Make felling cut five centimeters higher than lower notch cut and on opposite side of tree (see Figure 13). Keep felling cut parallel to lower notch cut.

2.Cut towards notch.

4.When tree begins to fall, quickly

•remove saw from felling cut

•release trigger to turn saw off

•put saw down

•exit area using retreat path

!WARNING

Be alert for falling overhead limbs. Watch your footing while exiting area.

LIMBING A TREE

!WARNING

Avoid kickback. Kickback can result in severe injury or death. See Kickback, page 3 to avoid risk of kickback.

!WARNING

When cutting limb that is under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, limb could spring back and strike operator causing severe injury or death.

!WARNING

Do not cut all the way through tree. Leave about five centimeters of tree diameter uncut directly behind felling notch (see Figure 13). This uncut portion acts as a hinge. The hinge helps keep tree from twisting and falling in wrong direction.

 

 

Direction of Fall

3rd Cut -

 

Hinge

Felling Cut

 

2nd Cut -

 

 

 

 

Upper

 

5 cm

Notch Cut

 

 

5 cm

 

1st Cut -

 

 

 

 

Lower

 

 

Notch Cut

!CAUTION

Seek professional help if facing conditions beyond your ability.

Limbing is removing branches from a fallen tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 14). Clear cut limbs from work area often. This will help maintain a safe work area.

Make sure you start your cut where limb will not pinch saw during cutting. To avoid pinching, start cut on freely hanging limbs from above limb. Start cut on limbs under tension from under limb. If pinch occurs, turn saw off, lift limb, and remove saw.

Figure 13 - Felling A Tree

3. As felling cut nears hinge, tree should begin to fall. Note: If needed, drive wedges into felling cut to control direction of fall. If tree settles back and pinches chain, drive wedges into felling cut to remove saw. Only use wedges made of wood, plastic, or aluminum. Never use wedge made of steel. This

could cause kickback and damage to chain.

Figure 14 - Limbing A Tree

 

10

100273

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Contents Electric Chain SAWSymbols InformationBefore Operating Chain SAW Safety WarningsKickback Safety Devices On This Saw KickbackPushback and PULL-IN Saw Maintenance and Kickback SafetyMaintenance and Storage of Chain SAW Cause Of Pushback and Pull-InProduct Identification Chain SAW Names and TermsSprocket Support Adjusting Block Plate Screw AssemblyGuide Bar Nuts Sprocket Support Adjusting Hole UnpackingFilling OIL Tank SAW Chain Tension AdjustmentGuide Bar Nuts Correct Gap Tension Incorrect Tension Oiling Chain Operating Chain SAWExtension Cords Cutting with the Chain SAWBefore Felling a Tree Trimming a Tree PruningFelling a Tree Cutting Down a Tree Retreat Path Direction of Fall TreeFelling Procedure Limbing a TreeLog Supported On Both Ends Bucking a LOGLog Supported On One End Entire Length Of Log On GroundCare of Guide BAR Cleaning and MaintenanceCleaning SAW Body Sharpening Your SAW ChainRight side of chain Sharpening CuttersFiling Cutter Depth Gauges Depth Gauge Flat File Tool SlotStorage Replacement PartsRecycling Replacing Saw ChainTroubleshooting Observed Fault Possible Cause RemedyKeep this Warranty Warranty InformationLimited Warranty Electric Chain SAW

100271-01 specifications

Remington Power Tools' 100271-01 is a versatile and powerful addition to any homeowner's or professional's tool collection. This electric chainsaw is designed for cutting and pruning tasks, providing both convenience and efficiency. One of its standout features is its robust 16-inch bar and chain, which allows for cutting through a variety of wood sizes with ease. This length is perfect for tackling small to medium-sized trees and branches, making it an ideal choice for yard maintenance.

The 100271-01 is equipped with a powerful 12-amp motor, providing ample power to handle tough jobs. This electric chainsaw eliminates the hassle of fuel, ensuring that users can start their work with the push of a button. The benefits of an electric chainsaw include reduced emissions, quieter operation, and less maintenance compared to gas-powered counterparts. The lightweight design enhances maneuverability, reducing user fatigue during prolonged use.

Safety is also a top priority in the design of the Remington 100271-01. It comes with a chain brake feature that automatically stops the chain if kickback occurs, providing peace of mind during operation. Additionally, the unit includes a low kickback chain that further minimizes the risk of injury, making it suitable for both novice and experienced users. The easy-to-use tensioning system allows users to adjust chain tension quickly and without the need for additional tools, ensuring efficient and safe operation.

Another significant feature of the Remington 100271-01 is its ergonomic design. The handle is designed for comfort, offering a secure grip to reduce hand strain during extended use. This design consideration is crucial for users who may need to perform multiple cuts or work for extended periods.

In conclusion, the Remington Power Tools 100271-01 chainsaw combines power, safety, and user-friendly features. With its 16-inch bar, 12-amp motor, and focus on ergonomics and safety, it stands out as an excellent choice for anyone looking to maintain their outdoor space efficiently and effectively. Whether you are trimming branches or cutting firewood, this chainsaw provides the performance and reliability needed for a wide range of cutting tasks.
Top Page Image Contents