Scag Power Equipment STT-31EFI-SS operating instructions Charging the Battery, Jump Starting

Page 41

Section 7

R

7.7 Battery

WARNING

Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. Keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.

WARNING

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm. Wash hands after handling.

WARNING

Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEVERE CHEMICAL BURNS. Avoid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NOT tip any battery beyond 45° angle in any direction. If fluid contact does occur, follow first aid suggestions below.

BATTERY ELECTROLYTE FIRST AID

External Contact — Flush with water.

Eyes — Flush with water for at least 15 minutes and get medical attention immediately.

Internal — Drink large quantities of water. Follow with Milk Of Magnesia, beaten egg, or vegetable oil. Get medical attention immediately. In case of internal contact, DO NOT give fluids that would induce vomiting.

A. Charging the Battery

Refer to the battery charger’s manual for specific instructions.

Under normal conditions the engine’s alternator will have no problem keeping a charge on the battery. If the battery has been completely discharged for a long period of time, the alternator may not be able to recharge the battery, and a battery charger will be required.

DO NOT charge a frozen battery. It may explode and cause injury. Let the battery warm before attaching a charger.

Whenever possible, remove the battery from the mower before charging and make sure the electrolyte covers the plates in all cells.

WARNING

BATTERIES PRODUCE EXPLOSIVE GASES. Charge the battery in a well ventilated space so gases produced while charging can dissipate.

Charging rates between 3 and 50 amperes are satisfactory if excessive gassing or spewing of electrolyte does not occur or the battery does not feel excessively hot (over 125°F). If spewing or gassing occurs or the temperature exceeds 125°F, the charging rate must be reduced or temporarily stopped to permit cooling.

B. Jump Starting

1.The booster battery must be a 12 volt type. If a vehicle is used for jump starting, it must have a negative ground system.

2.When connecting the jumper cables, connect the positive cable to the positive battery post, then connect the negative cable to the negative battery post.

37

Page 40 Page 42
Image 41
Page 40 Page 42
Contents OPERATOR’S Manual STT-31EFI-SS STT61V-31EFI-SSWith a serial number E3700001 to E3799999 Table of Contents Following Section AdjustmentsGeneral Information USE only Scag Approved Attachments and AccessoriesIntroduction Direction ReferenceSTT Models SymbolsSymbol Description Signal Words Safety InformationThis symbol means Attention! Become Alert! Your Signal WordOperation Considerations Section Foldable Roll-over protection system if equipped Roll-Over Protection SystemFoldable Roll-Over Protection System Using a spark arrestor Maintenance Considerations & StorageSafety And Instructional Decals Install Belt COvER Before Power Head SpecificationsEngine ElectricalHydraulic System Weights And DimensionsCutter Deck Controls And Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemStarting The Engine Initial Run-In ProceduresGround Travel And Steering Forward TravelReverse Travel Engaging The Deck Drive Cutter BladesParking The Mower Hillside OperationAfter Operation Removing Clogged MaterialRecommendations For Mowing Adjusting Cutting HeightMoving Mower With Engine Stopped Adjusting The Height Adjust Pedal Adjusting The Steering LeversTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsGround Wavy High-Low Appearance, Scalloped E v e n C u t o n F l atCut, or Rough Contour Sloping Ridge AcrossDirt or CuttingVery Close To the Ground Scalping Blades HittingStep Cut Ridge in Center Cutting pathBrake Adjustment AdjustmentsRH Steering Control Rod Adjustment Neutral AdjustmentTracking Adjustment Throttle Control and Choke AdjustmentsCutter Deck Pitch Cutter Deck LevelCutter Deck Height Cutter Deck Height AdjustmentPosition Custom-Cut Baffle Adjustment Current Production Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment Early Models Position Custom-Cut Baffle Adjustment Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceProcedure Comments Break-In 100 200 500 First HoursLocation Lubrication Interval Lubricant NO. Places LubricationLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilReplacing In-Line Fuel Filter Elements Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Charging the Battery BatteryBattery Electrolyte First AID Jump StartingDrive Belts Blade ReplacementCutter Blades Blade InspectionChecking Lubricant Level TiresCutter Deck Gearbox Cooling System Cleaning the Radiator Debris ScreenChanging Lubricant Checking Coolant LevelChecking The Fan Belt Tension Body, Deck, And UpholsteryScag Approved Attachments And Accessories Illustrated Parts ListIllustrated Parts List 61V & 72VS Cutter Decks Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Fender Weldment, RH Bolt, Hex Hd., 5/16-18 x 1, Zinc 43606 STT ROLL-OVER Protection System with Suspension Seat STT ROLL-OVER Protection System with Suspension Seat Deck Drive Components Belt Guard, Rear Hinge, Belt Guard 481309 Latch, Hood 482845 Engine & Attaching Parts 31HP-EFI Kohler Available through the individual engine manufacturer Brake and Steering Components Grip, Handle Bar Fuel and Hydraulic System Kohler 31EFI 24 403 BDP-16A Hydraulic Pump Assembly with Cooling FAN HG70924 Charge Pump Kit .19 STD. Splined HG51457 Electrical System 31HP-EFI Kohler Electrical System 31HP-EFI Kohler Heavy-Duty Commercial STT-EFI Decals Page2 Electrical Schematic Kohler 31HP EFI Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Radiador del desechos de criba la de Limpieza .B Tapicería y plataforma CuerpoVentilador del correa la de tensión la de Verificación .C NotaCorte de plataforma La de cambios de CajaRefrigeración de Sistema Cuchilla la de Reemplazo .C LlantasNota Cuchilla la de Reemplazo .8-7 Figura Corte de cuchillas con trabajar al ojos yTransmisión de Correas Corte de CuchillasCuchilla la de Inspección .A Puente por Arranque .BBatería la de Carga .A BateríaAgua con Enjuague externo Contacto Batería DE Electrolito Para Auxilios PrimerosAire de filtro del elemento del reemplazo y/o Limpieza .A Motor del aire de FiltroLínea en combustible de filtro Del elementos los de Reemplazo .BMotor del Aceite Motor del combustible de SistemaHidráulico aceite de Filtro .3-7 Figura Hidráulico SistemaHidráulico aceite de nivel del Verificación .A Conexión de puntos de Lubricación .1-7 Figura Horas LubricaciónCiones Lubricación Ubica Lubricante Ubicación DE Intervalo Recomendados servicio de Intervalos mantenimiento de Tabla MantenimientoMontaje de accesorios de Ubicación Montaje de Ranura Posiciones 3 de personalizado corte de deflector del Ajuste Personalizado corte de deflector del AjustePosiciones 7 de personalizado corte de deflector del Ajuste Corte de plataforma la de Tope .8-6 Figura Corte de plataforma la de AlturaCorte de Plataforma la de altura de Ajuste .7-6 FiguraCorte de Plataforma la de nivel del Ajuste .5-6 Figura Corte de plataforma la de InclinaciónCorte de plataforma la de Nivel Alineación de Ajuste Estrangulación y aceleraciónDe controles los de Ajustes Neutral Ajuste Desplazamiento de AjustesEstacionamiento de freno del Ajuste AjustesFreno de varilla la de Ajuste .2-6 Figura Freno del vAjuste .1-6 FiguraLa de ancho del través Corte de trayectoriaInclinadas Crestas Inclinado CorteInclinadas Salientes La de ancho lo aIrregular perfil o Volado corte onduladaEntre cortar sin césped Corte de trayectoriasDe Franjas Vetas La en cortar sin céspedAltura la de ajuste de pedal del Ubicaciones .8-4 Figura Opcional enganche de accesorio RemolqueDirección de palancas las de Ajuste Altura de ajuste de pedal del AjusteDirección De palancas las de Ajuste .7-4 Figura Plataforma la de liberación de Palanca .6-4 FiguraCésped el Corte de altura la de AjusteCortar para Recomendaciones Detenido motor el con cortacésped del DesplazamientoOperación la de Después Atascado material del RetriroCortacésped del Estacionamiento Cuesta una en OperaciónReversa en Desplazamiento Corte de cuchillas plataforma de transmisión la de ConexiónCortador Del accionamiento de Interruptor .3-4 FiguraMotor del Arranque Dirección y terreno el en DesplazamientoInicial arranque de Procedimientos Adelante hacia DesplazamientoDescarga de válvula de Control .2-4 Figura Seguridad de bloqueo de SistemaLa Indica .1-4 Figura combustible de Indicador Usado .1-4 Figura dirección de derecho ControlInstrumentos e Controles .1-4 Figura Operación DE InstruccionesInstrumentos e controles de Identificación Productividad Dimensiones y PesosPotencia de Cabezal EspecificacionesEléctrico Sistema MotorSeguridad de y instructivas Calcomanías REvErSA AdELAntEDe Consideraciones Chispas de supresor un UtiliceAlmacenamiento y mantenimiento Vuelco contra protección de plegable Sistema .1-2 Figura Muerte la o graves lesiones ocasionarMantener y inspeccionar de incumplimiento El Protección de Plegable Sistema Vuelco contra protección de SistemaEquipado viene si vuelco contra Peligro Operación de Consideraciones Información Seguridad DEOperación la a previas Consideraciones Señalización de PalabrasDescripción Símbolo SímbolosSTT Modelos Scag POR Aprobados Dispositivos USE Sólo General InformaciónInstrucciones de Referencia List Parts Illustrated 8 Sección Sección Sigue Comercial Equipo Limitada GarantíaMantenimiento 7 Sección Ajustes 6 SecciónEspecificaciones 3 Sección Operación DE Instrucciones 4 SecciónSeguridad DE Información 2 Sección General Información 1 Sección61V-SMT 72VS-SMTSS-31EFI-STT SS-31EFI-STT61VOperador DEL Manual

STT-31EFI-SS specifications

Scag Power Equipment is renowned for producing high-quality commercial mowing equipment, and the STT-31EFI-SS stand-on mower is no exception. Designed with professional landscapers in mind, the STT-31EFI-SS offers a perfect blend of power, efficiency, and maneuverability.

One of the standout features of the STT-31EFI-SS is its 31 hp EFI (Electronic Fuel Injection) engine. This powerhouse engine not only delivers impressive power but also enhances fuel efficiency. The EFI technology ensures that the engine operates at optimal performance by automatically adjusting the air-to-fuel ratio under varying conditions. This results in smoother starts, improved throttle response, and reduced emissions, making the mower both environmentally friendly and cost-effective in the long run.

The STT-31EFI-SS features a durable construction built to withstand the rigors of commercial use. Its robust steel frame and heavy-duty components are designed for maximum longevity. Moreover, the mower is equipped with Scag's cutting-edge Hydro-Gear ZT-3400 transmission, which offers exceptional speed and agility. This transmission allows operators to navigate tight spaces with ease and provides a top speed of up to 10.5 mph, making it ideal for large properties or demanding mowing tasks.

Operator comfort is another key aspect of the STT-31EFI-SS. The stand-on design promotes better visibility and quick maneuverability, enabling operators to navigate obstacles with confidence. The padded operator platform and adjustable controls ensure a comfortable experience, even during extended use. Additionally, the mower’s low center of gravity enhances stability on slopes and uneven terrain.

One of the most notable characteristics of the STT-31EFI-SS is its advanced cutting deck. The mower features a 48", 52", or 61" Velocity Plus cutting deck, which is known for delivering a superior cut and impressive grass dispersal. The deck is engineered for optimal airflow, enabling precision mowing while preventing clumping. This technology ensures that grass clippings are evenly distributed, resulting in a healthier lawn appearance.

In conclusion, the Scag STT-31EFI-SS stand-on mower integrates powerful performance, innovative engineering, and comfort. Featuring a reliable EFI engine, robust construction, and exceptional maneuverability, this mower stands out as an excellent choice for professional landscapers seeking efficiency and reliability in their equipment.
Top Page Image Contents